BSENISO527-4-1997塑料.拉伸性能测定.第4部分均质和非均质增强纤维塑料复合材料的检验条件.PDF,BRITISH STANDARD BS EN ISO 527-4:1997 I BS 2782-3: S B Method ) c 326F:1997 ( , y p o C d Plastics — e l l o r t n Determination of o c n U 6, tensile properties —
《ISO-527-4-1997.pdf》由会员分享,可在线阅读,更多相关《ISO-527-4-1997.pdf(14页珍藏版)》请在人人文库网上搜索。 international standard is0 527-4 first edition 1997-04-15 plastics - determination of tensile properties - part 4: test conditions for isotropic and orthotropic fibre-reinforced ...
Contact address E-mail : yuji.ito@tuv-sud.co.th TEL : +66-2564-7847 (Ext. 527) Yuji ITO Automotive Homologation Manager (ASEAN) TÜV SÜD (Thailand) Ltd. from Jan. 2014. History 1981 – 1999 Worked for vehicle manufacturer in R&D Div., in charge of Engine Development. 1999 – 20...
DIN EN ISO 527-4-1997 塑料.拉伸性能测定.第4部分均质和非均质增强纤维塑料复合材料试验条件
ISO 527-4 ISO 535 ISO 5361 ISO 5370 ISO 5476 ISO 5593 ISO 5667-1 ISO 5677 ISO 5722 ISO 5803 ISO 5817 ISO 583 ISO 6085 ISO 6181 ISO 6502-3 ISO 6612 ISO 6613 ISO 7001 ISO 7142 ISO 7152 ISO 7209 ISO 734 ISO 7582 ISO 7704 ISO 7784-1 ISO 7870-2 ISO 8000-117 ISO 8000-51 ISO...
标准号:ISO 527-1:2019 EN 标准名称:塑料 拉伸性能的测定 第1部分:一般原则 英文名称:Plastics — Determination of tensile properties — Part 1: General principles 标准状态:现行 发布日期:2019-07-26 文档简介 一般原则主要内容如下: 该标准规定了塑料材料拉伸性能的测定方法、测试设备、试验程序和结果评估等...
中文翻译:ISO 527-2:2012.pdf 规定了根据ISO 527-1中给出的一般原则确定成型和挤出塑料的拉伸性能的试验条件 英文原版:ISO 527-2:2012.pdf specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527‑1. ...
拉伸测试ISO标准-总则解析
ISO 527 ISO 527 一.断裂强度 样品数量:不少于5个 样条类型:1B L3=150mm L=115mm±1.0 L1=60mm±0.5 L0=50mm±0.5 b2=20mm±0.2 h=4.0mm±0.2 b=10mm±0.2 速度:选择速率应变速率尽可能接近1%L3/min,常规:10mm/min 当测量最大伸长和弹性拉伸模量的测定时速率为2mm/min 测试程序:1. 试样...
4.试验程序:拉伸试验应按照标准规定的程序进行,包括加载速度、保持时间、卸载和结果计算等。 5.结果评估:试验结果应进行评估,包括测量误差、合格判定和性能指标等方面。 ISO527-2:2012标准为塑料拉伸性能的测定提供了一套系统、规范和准确的试验方法,有助于保证塑料制品的质量和可靠性。在进行塑料拉伸性能测试时,应按...