isis timer holding-multiplier命令用来配置Hello报文的发送间隔时间的倍数,以达到修改IS-IS的邻居保持时间的目的。 undo isis timer holding-multiplier命令用来恢复Hello报文的发送间隔时间的倍数为缺省值3。 缺省情况下,Hello报文的发送间隔时间的倍数值为3,即邻居保持时间为Hello报文的发送间隔时间的3倍。
HUAWEI] isis [HUAWEI-isis-1] network-entity 01.0000.0000.0001.00 [HUAWEI-isis-1] quit [HUAWEI] interface gigabitethernet 1/0/1 [HUAWEI-GigabitEthernet1/0/1] undo portswitch [HUAWEI-GigabitEthernet1/0/1] isis enable 1 [HUAWEI-GigabitEthernet1/0/1] isis timer holding-multiplier 6 level-2...
IS-IS的hello默认情况下发送是10s,holding timer是3倍于hello。 [AR1-GigabitEthernet0/0/0]isis timer hello 30--修改hello时间 [AR1-GigabitEthernet0/0/0]isis timer holding-multiplier 4--倍数 1. 2. E、ISIS的数据库同步 ISIS hodetime(生存时间LSP)---1200S(默认),计数方式为倒数计数。 周期...
Level-1:负责区域内路由,也就说L1路由器只能存在一个区域内,也只能跟区域内的路由器建立邻居,也只会创建这个区域的数据库,也只会计算这个区域内的路由。 Level-2:负责区域间路由,L2路由器不但负责骨干区域,而且还会和L1/2建立邻居,所以L2会负责区域间的路由。 Level-1/2:负责区域内和区域间路由,因为他既有L1...
某网络通过部署IS-IS实现全网互通, 若在一台IS-IS路由器的某接口下配置命令isis timer holding-multiplier 5 level-2, 则以下关于该场景的描述, 正确的是哪一项 A、 该接口为点对点链路接口 B、 该接口Level-1邻居保持时间为30秒 C、 该接口发送Leve-2的Hello报文的间隔时间是5秒 D、 该接口Level 2...
邻居的Level级别: L1:Level-1 L2:Level-2 L12:Level-1-2 IPv6 BFD State IPv6 BFD状态 up:IPv6 BFD会话成功建立 down:IPv6 BFD会话建立失败 TX 经过协商后IPv6 BFD报文的最小发送间隔 RX 经过协商后IPv6 BFD报文的最小接收间隔 Multiplier 远端的检测倍数 ...
To set this value, run the isis timer holding-multiplier command. LSP-Throttle Timer Interval for sending LSPs or CSNPs and number of LSPs or CSNPs that are sent each time. To set the two values, run the isis timer lsp-throttle command....
To set the interval for sending Hello packets, run the isis timer hello command. Holding-Multiplier Number of consecutive Hello packets that are not received before the neighbor is declared Down. To set this value, run the isis timer holding-multiplier command. LSP-Retransmit Interval for retra...
DIS Hello Timer Value DIS发送Hello报文的时间间隔。该字段的值是Hello Timer Value的1/3,只有当接口为DIS时,该字段的值才有效 Hello Multiplier Value 宣告邻居失效前没有连续收到的Hello报文数目,通过命令isis timer holding-multiplier可以配置此Hello报文的数目。 LSP-Throttle Timer 发送LSP或CSNP报文的间隔时间和...
To set the interval for sending Hello packets, run the isis timer hello command. Holding-Multiplier Number of consecutive Hello packets that are not received before the neighbor is declared Down. To set this value, run the isis timer holding-multiplier command. LSP-Retransmit Interval for retra...