接口LDP联动状态变化。 日志参数 参数名称参数含义 [process-id] IS-IS进程号。 [SyncPreviousState] 变化前的联动状态。 [SyncCurrentState] 变化后的联动状态。 IfName 接口名称。 可能原因 接口LDP联动状态变化。 处理步骤 任意视图下执行命令display isis ldp-sync interface,查看Sync State、LDP State...
LDP LSPM LBDT LLDP LOOPDETECT MAD MBR MCAST MGMD MPLS MRM MSDP MSTP MONITOR NQA NETSTREAM NTP OSPF OSPFV3 PIM PIM-STD PKI PM PoE PTP RDS RIP RM RMON RRPP RSVP SCMTRAP SECE SINDEX SNMP SOCKET SRM SSPADP SW_SNPG SYSMIB SYSRES TPLMNG TRUNK TUNNEL USBLOAD UNI-TOPOMNG UVM VBST VCMP ...
接口开销来源是LDP配置的接口开销值 enabled by rui cost 接口开销来源为继承RUI路由的开销 enabled by silent cost 接口视图下配置isis silent后的开销值 enabled by tunnel cost 配置TE Tunnel后得到的链路开销值 IPv6 prefix effective cost 接口的IPv6路由开销 Flags 开销标记 R-Relative cost:相对开销值...
Router(config)# router isis Router(router-config)# fast-reroute remote-lfa level-2 mpls-ldp Related Commands Command Description router isis Enables the IS-IS routing protocol and specifies an IS-IS process. fast-reroute tie-break To configure the Fast Reroute (FRR) tiebreaking priority,...
ISIS/6/LDP_INFORM_RM_DISAB ISIS/6/LDP_INFORM_RM_ENAB ISIS/6/LDP_INTF_NOT_ENABLE ISIS/6/LDP_INVALID_MSG ISIS/6/LDP_STA_HD_TMR_FAIL ISIS/6/LDP_STA_HMC_TMR_FAIL ISIS/6/LDP_STP_HD_TMR_FAIL ISIS/6/LDP_STP_HMC_TMR_FAIL ISIS/6/LEAVE_L1_ADDR_FAIL ISIS/6/LEAVE_L2_ADDR_FAIL ISIS...
If you are using LDP, you cannot use theroute-targetcommand when configuring a VRF. The router will use BGP for Multiprotocol Label Switching (MPLS) labels. Information About IS-IS Support for an IS-IS Instance per VRF for IP VRF-Aware IS-IS ...
Message ISIS/6/LDP_STP_HD_TMR_FAIL:ISIS failed to delete HoldDown timer on interface [interface-name]. Description Failed to delete the HoldDown timer on the interface. Parameters Parameter NameParameter Meaning [interface-name]Indicates the name of an interface. ...
ISIS notified the RM that LDP synchronization was disabled on the interface. Parameters Parameter NameParameter Meaning [process-id]Indicates the ID of an ISIS process. [interface-name]Indicates the name of an interface. Possible Causes ISIS and LDP synchronization was disabled. ...
接口LDP联动状态变化。 日志参数 参数名称参数含义 [process-id] IS-IS进程号。 [SyncPreviousState] 变化前的联动状态。 [SyncCurrentState] 变化后的联动状态。 IfName 接口名称。 可能原因 接口LDP联动状态变化。 处理步骤 任意视图下执行命令display isis ldp-sync interface,查看Sync State、LDP State...
enabled by igp ldp 接口开销来源是LDP配置的接口开销值 enabled by rui cost 接口开销来源为继承RUI路由的开销 enabled by silent cost 接口视图下配置isis silent后的开销值 enabled by tunnel cost 配置TE Tunnel后得到的链路开销值 IPv6 prefix effective cost ...