SC18IS600IBS - SPI至I2C总线接口 - SPI 从设备至I²C 主设备/GPIO电桥 - 电桥 - 恩智浦, LLC 产品描述 SC18IS600可用作主机(微控制器、微处理器、芯片组等)标准SPI和串行I2C总线之间的接口。允许主机与其他I2C总线器件直接通信。SC18IS600用作I2C总线主发送器或主接收器。SC18IS600控制所有I2C总线特定...
SC16IS750IPW是恩智浦公司的一款I²C/SPI从设备至UART/IrDA/GPIO电桥产品,SC16IS750IPW是带有I2C总线/SPI接口、64字节发送和接收FIFO以及IrDA SIR内置式支持的单通道UART,本站介绍了SC16IS750IPW的封装应用图解、特点和优点、功能等。
more code-efficient bit-oriented math A high-speed 12-bit analog-to-digital converter Embedded 1.2 V voltage reference for ADC A high-speed analog comparator Low-power UART, SPI, I2C (high speed
this is a supervisory software that connects to the supervisory computer via a USB interface. The supervisory computer automatically selects the protocol for the subordinate machine by configuring the parameters of I2C/SPI/UART protocols, and then burns
An Arduino library for 3-Axis Digital Accelerometer ±2g to 16g (LIS3DHTR).Acceleration data can be obtained using IIC interface and SPI interface. How to install Arduino Library please referhere. Usage //This example use I2C.#include"LIS3DHTR.h"#include<Wire.h>LIS3DHTR<TwoWire> LIS;/...
An alternative device is the MCP23S17 which is uses the SPI interface that can operate at 10MHz (a lot faster than the I2C version). This SPI device has the same number and arrangement of pins, but uses two unused (I2C) pins to implement the SPI interface. In all other respects it op...
i2cspi.begin(0); To send a byte 0x55 and simultaneously receive a byte from SPI 1 received_byte=i2cspi.transfer(0x55); To set gpio0 as an input pin 1 i2cspi.pinMode(0,INPUT); To set gpio0 as an output pin 1 i2cspi.pinMode(0,OUTPUT); ...
SC16IS接口是否可逆? 我正在考虑使用 SC16IS760(带 I2C/SPI 接口的单 UART)连接 MCU 和传感器设备。MCU 有一个 UART 端口,传感器 I/O 是 I2C。SC16IS 可以桥接这两者吗?我 自我清欢 2023-03-30 08:02:20 SC系列(SC-16S) 低频率小型SMD石英晶振 SC-16S 32.768KHZ 12.5PF/20PPM `SC系列(SC-16S)...
需要金币:*** 金币(10金币=人民币1元) 电子技术 数字集成电路周立功 SC16IS752,SC16IS762带I2C总线和SPI总线的接口芯片数据手册.pdf 关闭预览 想预览更多内容,点击免费在线预览全文 免费在线预览全文 电子技术数字集成电路周立功SC16IS752,SC16IS762带I2C总线和SPI总线的接口芯片数据手册用户手册产品说明书使用说明...
Hi all, 2 of our 1562 APs are not joining WLC9800. When consoled to AP found out that AP is going to U-Boot and keeps rebooting instead to finding controller. Already tried to reset env and changed partitions Here is the complete output of AP