此影片展示了Cisco IOS路由器中IPv6本地鏈路地址和全局單播地址之間的主要區別: 路由器R1 hostname R1 ! ipv6 cef ! ipv6 unicast-routing ! interface Loopback10 no ip addressipv6 address FD10::/64 eui-64!--- Assigned a IPv6 unicast address in EUI-64 format.ipv6 ospf 1 area 1!--- Enable...
步骤1.确保在全局配置模式下配置了ipv6 unicast-routing命令。 步骤2.确保本地网络中的接口配置了有效的IPv6地址。 ipv6 unicast-routing! Enable IPv6 Routing. In absence of this command ! ! the Router does not send any ICMPv6 RA packet.interface GigabitEthernet0/0/0 ipv6 address 2001...
Theipv6 unicast-routingcommand globally enables IPv6 and must be the first IPv6 command executed on the router. The ipv6 address command assigns the prefix, the length, and the use of EUI-64 to assign the interface ID. Optionally, you can omit the eui-64 parameter and configure the entir...
number of IPv6 multicast groups:0number of IPv6 unicast routes:0number of directly-connected IPv6 addresses:0number of indirect IPv6 unicast routes:0number of IPv4 policy based routing aces:0number of IPv4/MAC qos aces:0.5K number of IPv4/MAC security aces: 1K number of IPv6 policy based...
其中ip cef命令我这设备提示不完整% Incomplete command.经查资料show ipv6 cef是有显示的,应该是已经打开了。我的路由器ipv6有关配置如下:!ip dhcp pool Localnetwork 192.168.10.0 255.255.255.0default-router 192.168.10.1 dns-server 192.168.10.1! ! ! subscriber templatingipv6 unicast-routingipv6 dhcp ...
环境为R1---R3的E0口连接,分别启用loopback10接口,在全局模式下启用ipv6 unicast-routing ,和ipv6 rip 路由进程;在接口启用ipv6 enable,并且在接口启用ipv6 rip的路由。需要注意的地方,ipv6 ripCisco,Cisco是进程的表示。在接口下的rip路由要与进程中的表识相同,并且大小写敏感。 ipv6...
R2#sh bgp ipv6 unicast 2001:1::1/128 BGP routing table entry for 2001:1::1/128, version 0 Paths: (1 available, no best path) Not advertised to any peer Refresh Epoch 1 1 2001:12::2 (inaccessible) from 12.1.1.1 (12.1.1.1) ...
Source Packet Routing in Networking (SPRING) Working Group temporarily set up a dedicated design team to discuss SRv6 compression requirements and analyze existing solutions. The design team consists of experts from multiple companies such as China Mobile, China Telecom, Huawei, Cisco, Juniper, Nokia...
labeled-unicast { explicit-null; } } export RR-Export-All; neighbor 95.176.255.254 { description C7201-RR-IP-CIGALETOVA; local-address 95.176.254.10; } neighbor 95.176.255.252 { description C7201-RR-IP-CIGALETOVA; local-address 95.176.254.10; } } By the cisco command above, shouldn'...
If the Echo Request message was sent to a unicast address, the Source address of the Echo Reply message must be the same as the Destination address of the Echo Request message. If the Echo Request was sent to an IPv6 multicast address, the Source address of the Echo Reply must be a ...