执行命令ipv6 enable,重新使能以太网接口的IPv6功能。 执行命令ipv6 address{ipv6-address prefix-length|ipv6-address/prefix-length},重新配置以太网接口的IPv6地址。 执行命令loopbacklocal,重新配置以太网接口的内环回功能。 否执行步骤2。 否执行步骤2。
查看接口的物理状态是否Up,如果接口的物理状态为DOWN,则请检查物理连接是否正常。 查看接口是否使能了IPv6功能,如果没有使能IPv6功能,则请执行命令ipv6 enable使能IPv6功能。 查看接口的IPv6地址状态是否正常。 如果接口的IPv6地址后面没有[TENTATIVE]或者[DUPLICATE]信息,表明IPv6地址状态正确。 如果回显中IPv6地址出...
peer ip-address enable undo peer ip-address enable 【视图】 BGP-IPv6子地址族视图 【参数】 ip-address:6PE对等体的IPv4地址。 【描述】 peer enable命令用来使能特定的6PE对等体。undo peer enable命令用来取消此配置。 & 说明: S3610&S5510系列以太网交换机目前不支持此命令。 【举例】 S3610&S5510系列...
Uncomment the line which containsnet.ipv6.conf.default.forwarding=1. This is a common step to enable IPv6 routing. You can learnhow to install and enable DHCPv6 on your network here. Alternatively, if you want to use radvd which will advertise your prefix and let the network's systems sel...
networks:ip6net:enable_ipv6:trueipam:config:-subnet:2001:db8::/64 You can now run containers that attach to theip6netnetwork. $docker run --rm --network ip6net -p 80:80 traefik/whoami This publishes port 80 on both IPv6 and IPv4. You can verify the IPv6 connection by running cur...
ipv6 netstream aggregation { as | bgp-nexthop | destination-prefix | prefix | protocol-port | source-prefix }缺省情况下,未配置IPv6 NetStream流聚合方式。(3) 开启聚合视图对应的聚合功能。enable缺省情况下,当前聚合视图对应的聚合功能处于关闭状态。(4) 配置IPv6 NetStream聚合统计信息输出的目的地址和...
Use theipv6 addresscommand in Interface Configuration mode to configure a global unicast IPv6 address based on an IPv6 general prefix and enable IPv6 processing on an interface. To remove the address from the interface, use thenoform of this command. ...
This task explains how to assign IPv6 addresses to individual router interfaces and enable the processing of IPv6 traffic. By default, IPv6 addresses are not configured and IPv6 processing is disabled. You can configure IPv6 addresses on the following interface types: •Gigabit Etherne...
root@pve:~# cat /etc/network/interfaces # network interface settings; autogenerated # Please do NOT modify this file directly, unless you know what # you're doing. # # If you want to manage parts of the network configuration manually, # please utilize the 'source' or 'source-directory'...
# Ubuntu忽略,CentOS执行 # 安装最新的内核 # 我这里选择的是稳定版kernel-ml 如需更新长期维护版本kernel-lt yum -y --enablerepo=elrepo-kernel install kernel-ml # 查看已安装那些内核 rpm -qa | grep kernel # 查看默认内核 grubby --default-kernel # 若不是最新的使用命令设置 grubby --set-default...