ipv6 nd learning strict ipv6 nd ns multicast-enable ipv6 nd ns retrans-timer ipv6 nd nud reachable-time ipv6 nd ra ipv6 nd ra halt ipv6 nd ra hop-limit ipv6 nd ra preference ipv6 nd ra prefix ipv6 nd ra route-information ipv6 nd ra router-lifetime ipv6 nd stale-timeout ipv6...
当设备上使能发送ND协议报文功能后,普通接口(如GE接口)会自动发送组播NS报文主动学习ND表项或者通过响应NS报文的方式被动学习ND表项。但由于终结子接口不能发送组播NS报文而是将该组播NS报文丢弃,所以为了允许终结子接口能发送组播NS报文,可以通过在终结子接口上执行命令ipv6 nd ns multicast-enable使能终结子接口发送组...
前往Controller索引標籤>Multicast頁面和Enable MLD Snooping以支援多點傳送IPv6流量。若要啟用IPv6多點傳送,還必須啟用控制器的全域多點傳送模式。 注意:如果需要點對點發現應用程式(如Apple的Bonjour),則應啟用全域性組播模式、IGMP和MLD監聽。 要驗證IPv6組播流量是否被監聽,請轉到Monitor頁籤和Multicast頁面。請注意,同時...
ipv6 nd unsolicited-na-learning enable 缺省情况下,接口不学习未经请求的NA报文中的邻居信息到ND表项中。 2.6 配置STALE状态ND表项的老化时间 1. 功能简介 为适应网络的变化,ND表需要不断更新。在ND表中,处于STALE状态的ND表项并非永远有效,而是有一个老化时间。到达老化时间的STALE状态ND表项将迁移到DELAY状态...
表1-17 配置ND Snooping功能 操作 命令 说明 进入系统视图 system-view - 使能IPv6转发功能 ipv6 必选 进入VLAN视图 vlan vlan-id - 使能ND Snooping功能 ipv6 nd snooping enable 必选 缺省情况下,ND Snooping功能处于关闭状态 退回系统视图 quit - 进入二层以太网端口视图/二层聚合接口视图 inte...
所有报文都基于ICMPv6报文。 (5)前缀重新编址 (6)重定向 (7)IPv6 FHS(IPv6 First Hop Security) 1)Core:RA Guard;DHCP Guard;IPv6 Snooping。 2)Advanced:Source/Prefix Guard;Destination Guard。 3)Performance and scalability:RA Throttler;ND Multicast Suppress。
较长时间才能完成,因而引入了“乐观的DAD”(RFC 4429) 注:CMTS中的DAD功能开启是在ipbundle下使能的:C158-C10G(ip-bundle 10)#ipv6 dad enable (DAD默认是开启的)LWF标准DAD过程(1) 在发送邻居请求(NS)前,接口必须加入全节点组播地址(FF02:1)和生成IPv6地址的请求节点组播地址(solicited-node multicast ad...
To enable IDS checks, use the following commands in global configuration mode: Command Purpose hardware ip verify address{destination zero|identical|reserved|source multicast} Performs the following IDS checks on the IPv6 address: destination zero...
switch(config-if-Et1/1#ipv6 nd dad proxy switch(config-if-Et1/1#ipv6 address 2001:db8:1::/64 switch(config-if-Et1/1#ipv6 enable To set the expiration time for the Neighbor Cache Table, use the following command: switch(config-if-Et1/1#ipv6 nd cache expire 1800 The expiration ...
Format no ipv6 nd ns-interval Mode Interface Config ipv6 nd other-config-flagThis command sets the “other stateful configuration” flag in router advertisements sent from the interface. Default false Format ipv6 nd other-config-flag Mode Interface Config ...