The gateway6 command is used to query and set the default IPv6 gateway of the MM910. Format smmget [ -l smm ] -d gateway6 smmset [ -l smm ] -d gateway6 -v ipv6addr Parameters Parameter Description Value ipv6addr The IPv6 address is in the format of...
Use theipv6 default-gatewayGlobal Configuration mode command to define an IPv6 default gateway. To remove the IPv6 default gateway, use thenoform of this command. Syntax ipv6 default-gateway{ipv6-address[outgoing-interface-id]} |interface-id no ipv6 default-gateway[{ipv6-address[outgoing-i...
host gateway=?命令,添加到目标应用服务器的路由。 执行add port ipv6_route eth_port_id=? default gateway=?命令,添加默认路由。 本命令不支持添加维护口的路由。 使用实例 为ID为“ENG0.A3.P0”的端口添加IPv6路由,目标网段地址为“fc00::0”,前缀长度为“32”,网关地址为“fc00::1”。ID和回显因...
Link-local IPv6 Address . . . . . : fe80::5850:6d61:1fb:ef3a%11 Default Gateway . . . . . . . . . : fe80::c801:b9ff:fef0:8%11 可以更改此行为,使Windows使用EUI-64进程。 netsh interface ipv6 set global randomizeidentifiers=disabled 您现在可以看到接口ID是使用EUI-64...
1.1.61 ipv6 nd ra prefix defaultipv6 nd ra prefix default命令用来配置通过RA消息发布的前缀使用的缺省参数。undo ipv6 nd ra prefix default命令用来恢复缺省情况。【命令】ipv6 nd ra prefix default [ valid-lifetime preferred-lifetime [ no-autoconfig | off-link ] * | no-advertise ]...
1.1.51 ipv6 nd ra prefix defaultipv6 nd ra prefix default命令用来配置通过RA消息发布的前缀使用的缺省参数。undo ipv6 nd ra prefix default命令用来恢复缺省情况。【命令】ipv6 nd ra prefix default [ valid-lifetime preferred-lifetime [ no-autoconfig | off-link ] * | no-advertise ]...
第二处是WAN6_GATEWAY=$这块 原始脚本 WAN6_GATEWAY=$(ip -6 route|grep -i'^default.*via'|grep -i-F"dev$WAN6_INTERFACE"|grep -i -o'via.*'|cut -d' '-f2|head -n 1)if[-z"$WAN6_GATEWAY"];thenlogger -t NAT6"Fatal error: No IPv6 gateway for$WAN6_INTERFACEfound"&&exit1 ...
You can also use the netsh interface ipv6 6to4 set relay command to specify the DNS name to query. If the query is successful, a default route is added using the 6to4 Tunneling Pseudo-Interface, and the next-hop address is set to the 6to4 address of the 6to4 relay router. The results...
Setting nameDescriptionNetsh.exe command equivalent 6to4 Relay NameAllows you to specify a 6to4 relay name for a 6to4 host. A 6to4 relay is used as a default gateway for IPv6 network traffic sent by the 6to4 host.netsh interface 6to4 set relay name= ...
Type: DeadGatewayDetection[] Position: Named Default value: None Required: False Accept pipeline input: False Accept wildcard characters: False-DefaultHopLimitSpecifies an array of values for the default hop limit. The cmdlet gets the IPv6 protocol configurations that have these values. The default...