Fortigate #config system gre-tunnelFortigate (gre-tunnel) #edit gre1Fortigate (gre1) #set interface firewallFortigate (gre1) #set local-gw 2.2.2.2Fortigate (gre1) #set remote-gw 1.1.1.1Fortigate (gre1) #end 执行set interface将GRE接口绑定到已有的Tunnel接口上,否则隧道协商不成功。 执行set lo...
new entry'firewall'added Fortigate (firewall)# set interface port03 Fortigate (firewall)# set mode main Fortigate (firewall)# set proposal 3des-sha1 Fortigate (firewall)# set psksecret Key@123 Fortigate (firewall)# set remote-gw 1.1.1.1 Fortigate (firewall)# set dhgrp 2 Fortigate (fire...
8. After you finally create the VPN tunnel, a summary page should appear to you showing all the options and configuration you had added to the FortiGate. Abdelrahman Reda Abdelrahman Reda is a Motivated Support Engineer with 6+ years of corporate and consumer support experience. His experience ...
Renato_MT New Contributor In response to Toshi_Esumi Created on 07-29-2022 03:53 PM Alguma soluçao para esse problema com esse erro faild to process pre-processos ph2 packet vpn ipsec. Estou fortigate 60-F com 10 tunnel com outros firewall ogasec, e com Mikrotic aprese...
FortiGate防火墙配置地址对象 创建本端和远端（Cisco ASA）的地址对象 使用web页面配置步骤 1.在Firewall > Address 选择“Create New”.2.按下面的内容输入相应数据:Address Name 地址组的名字，不影响配置，建议使用英文，这里hotel指Cisco端，horse指马房 Type 选择：Subnet/IP Range Subnet/IP Range 输入地址段...
Configure a firewall address that is applied in L2TP settings to assign IP addresses to clients once the L2TP tunnel is established. config firewall address edit "L2TPclients" set type iprange set start-ip 10.10.10.1 set end-ip 10.10.10.100 next end Configure a firewall policy. config fire...
Configure two firewall policies to allow bi-directional IPsec traffic flow over the IPsec tunnel: Configure HQ1: config firewall policy edit 1 set name "inbound" set srcintf "to_HQ2" set dstintf "dmz" set srcaddr "172.16.101.0" set dstaddr "10.1.100.0" set action a...
FortiGateIPSec⾼级选项配置 ⽬录 1.⽬的 (3)2.密钥周期(keylife) (3)3.保持存活(autokey keep alive) (4)4.⾃动协商 (5)5.NAT穿越(NAT traversal, 及keepalive) (6)6.对等体状态探测(DPD) (6)6.1 场景1 (7)6.1.1 拓扑图 (7)6.1.2 FGT_CQ的阶段1配置 (7)6.1.3 测试效果 (8...
Solved: Hello, I successfully configured a new VPN site-to-site between our Cisco FTD and a remote site that uses FortiGate. The issue is that we are not enabled to send traffic through this tunnel; all the ACPs and NAT Exemptions from our side are
Thanks for your reply, Firstly the FW/VPN device is a fortigate device which has set up another 3 similar IPSec with other routers at the other sites, only this one got a problem after peering with this firewall. I've done what you have instructed, please see the output: ...