6.2本标准若与其它规范文件相冲突时,依据顺序如下: 6.2.1本公司所提供的工程文件、组装作业指导书、返工作业指导书等提出的特殊需求; 6.2.2本标准; 6.2.3最新版本的IPC-A-610B规范Class1 6.3本规范未列举的项目,概以最新版本的IPC-A-610B规范Class1为标准。 6.4若有外观标准争议时,由质量管理部解释与核判...
公司已明确采用 IPC-A-610D Class 2 标准做为 公司是否明确规定采用 IPC-A-610 的哪级的标准作为 PCBA 3 PCBA 和(或) 电子组件的外观质量可接收标准 OK 和( 或) 电子组件的外观质量可接收标准? 。 已于产品相关图纸上进行明确标注,如型号为 TW-1095 ,PCB 主板组装图纸 (13-05-000177) 4 在相关图纸...
IPC-A-610国际标准中英文对照(17).pdf,IPC-A-610 国际标准中英文对照 4.6.2 Heat sink-Contact 散热片 ――接触片 arget-Class 1,2,3 目标——等级 1,2,3 · Component and heatsink are in full contact with the mounting surface. 组件和散热片与安装表面完全 接触 · Ha
Acceptable - Class 1,2,3 • The solder wets the tinned portion of the wire and pen- etrates to the inner strands of stranded wire. • Solder wicks up wire provided the solder does not extend to a portion of the wire that is required to remain flexible. • The tinning leaves a ...
5-焊点质量评定及IPC-A-610C(D)介绍 焊点质量评定及IPC-A-610D介绍 顾霭云
PCBA外观检验标准-(IPC-A-610E-完整)PCBA外观检验标准-(IPC-A-610E-完整)
焊点质量评定及 焊点质量评定及 IPC-A-610D介绍 IPC-A-610D介绍 顾霭云 顾霭云 无铅焊点的特点 无铅焊点的特点 ① 浸润性差,扩展性差。 ① 浸润性差,扩展性差。 ② 无铅焊点外观灰白、粗糙。 ② 无铅焊点外观灰白、粗糙。 ③ 无铅焊点中气孔较多,但气孔不影响机械强度。 ③ 无铅焊点中气孔较多,但气孔不...
IPC-A-610国际标准中英文对照 4.6.2 Heat sink-Contact 散热片――接触片 arget-Class 1,2,3 目标——等级1,2,3 · Component and heatsink are in full contact with the mounting surface.组件和散热片与安装表面完全 接触 · Hardware meets specified attachment requirements.部件满足规定的接触要求。Figur...
根据PCBA装配图要求引脚伸出要满足IPC-A-610 CLASS 3。 根据IPC-A-610E 表7-3可知引脚伸出最大1.5mm。 应用IPC-A-610的主观能动性案例分析 波峰焊后我们发现下列引脚超过1.5mm。 1. 连接器TB1(6 Pin) TB2(14 Pin) 应用IPC-A-610的主观能动性案例分析 2. 开关SW1 SW2(6 Pin) SW3(14 Pin) 应用...
IPC-A-610D 贴片元件焊锡标准 电子装配的可接受标准 Alinnaz