すみませんが、どなたかご教授下さい。 FTTH(PON)のコアNWなどで、ホスト間通信がL2レベルで制限される環境があると思います。 ※イメージ的にはPrivateVLANの独立ポートです。 ipv4では、local-proxy-arpを使ってL3デバイスがホスト間通信を中継/管理できると思うのですが
2.1.5 gratuitous-arp-sending enable 3 代理ARP 3.1 代理ARP配置命令 3.1.1 display local-proxy-arp 3.1.2 display proxy-arp 3.1.3 local-proxy-arp enable 3.1.4 proxy-arp enable 4 ARP Snooping 4.1 ARP Snooping配置命令 4.1.1 arp snooping enable 4.1.2 display arp snooping 4.1.3 reset arp snoo...
在集中式VXLAN IP网关组网中,请不要执行local-proxy-arp enable命令开启本地代理ARP功能。 1.5.2 配置集中式网关的网关接口 (1) 进入系统视图。 system-view (2) 创建VSI虚接口,并进入VSI虚接口视图。 interface vsi-interface vsi-interface-id (3) 配置VSI虚接口的IP地址。 ip address ip-address { mask ...
arp-proxy local enable 检查配置结果 执行命令display arp interface{interface-name|interface-typeinterface-number} ,查看基于接口查看ARP映射表。 翻译 收藏 下载文档 更新时间:2024-12-20 文档编号:EDOC1100304753 浏览量:42604 下载量:223 平均得分:
With local-proxy-arp the router would respond to arp requests for addresses on the same subnet (the subnet configured in the interface) Details: https://community.cisco.com/t5/routing/ip-local-proxy-arp/td-p/401851 https://community.cisco.com/t5/routing/proxy-arp/td-p/1560798 Regards! Exp...
local-proxy-arp enable distributed-gateway local 创建VSI虚接口VSI-interface2,并为其配置IP地址和MAC地址,该IP地址作为VXLAN 20内虚拟机的网关地址,指定该VSI虚接口为分布式本地网关接口,并开启本地代理ARP功能。 # interface Vsi-interface2 ip address 192.168.10.1 255.255.255.0 ...
With local-proxy-arp the router would respond to arp requests for addresses on the same subnet (the subnet configured in the interface) Details: https://community.cisco.com/t5/routing/ip-local-proxy-arp/td-p/401851 https://community.cisco.com/t5/routing/proxy-arp/td-p/1560798 Regards! Exp...
Proxy ARP is enabled Local Proxy ARP is disabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is enabled ...
Configuring Proxy ARP Anyway Configuring Intra-VLAN Proxy ARP Configuring Inter-VLAN Proxy ARP Configuring Local Proxy ARP Example for Configuring Routed Proxy ARP Configuring ARP Fast Reply Configuring Layer 2 Proxy ARP Enabling ARP Gateway Proxy Configuring ARP-Ping Configuring IP Address Conflict Detec...
If I understand the documentation correctly the cable proxy-arp command is the equivalent of the ip proxy-arp specifically for cable interfaces. Proxy-arp is the function of answering ARP requests for destinations not on the local segment. The assumption in ARP is that an end station will ARP...