ip link set <interface> up / down:如何调用脚本? Lat*_*ius2iprouteifconfig 根据发行版,调用ip link set <iface> up(或 down;还有 ifup / ifdown)将查看各种配置文件(Debian 上的 /etc/network/interfaces 我认为,Gentoo 有 /etc/conf.d/net...),并进行更改(例如与 DHCP 交互等) 据我所见strace,...
hrp track ip-link 1 master ip-link 1 状态down : HRP_M<BVS10-USG2210-2>dis ip-link 1 14:25:21 2013/04/30 num state timer vpn-instance ip-address interface-name mode vgmp 1 down 3 172.16.252.11 GE0/0/0.20 icmp master 告警信息 无。 处理过程 在防火墙上ping 172.16.252.11 HRP_M<BVS...
ip-link配置里面跟上探测的源地址解决。 ip-link name abc source-ip x.x.x.38 destination x.x.x.37 interface GigabitEthernet0/0/2 mode icmp next-hop x.x.x.37 ip-link name sdf source-ip y.y.y.2 destination y.y.y.1 interface GigabitEthernet0/0/3 mode icmp next-hop y.y.y.1 建...
sudo ip link set <interface_name> down && sudo ip link set <interface_name> up 1. 将<interface_name>替换为要重启的网络接口的名称,例如eth0或wlan0。这个命令将首先禁用指定的网络接口,然后重新启用它,以便更新其配置和状态。 如果您的网络接口有IPv4或IPv6地址、配置等独立的属性,您可以使用以下命令分...
interface Vlanif1012 ip address 10.1.2.1 255.255.255.0 *为VLAN1012配置IP地址,即该网段的网关地址 interface GigabitEthernet0/0/1 port link-type access port default vlan 8 *端口GigabitEthernet0/0/1属于VLAN8 interface GigabitEthernet0/0/2
[ ]undo info-center enable关闭信息中心 ,防止弹出日志 直连路由: direct route ,直接相连的路由,当路由器的接口配置好ip地址并up之后,会自动创建该路由。路由器默认情况下,只能 到达直连的网段。 undo xxx撤销某条指令 例如: int e0/0/1 undo ip address 例如: undo sysname...
[FW_A] ip-link check enable [FW_A] ip-link name test [FW_A-iplink-test] destination 1.1.1.1 interface GigabitEthernet 1/0/3 [FW_A-iplink-test] quit # 配置双机热备与IP-Link联动,由VGMP管理组监控IP-Link。当网络出接口故障时,IP-Link状态变为Down,VGMP管理组优先级降低2。
[FW1-zone-trust]add interface GigabitEthernet1/0/0 //把相应的接口加入安全区域 [FW1-zone-trust]qu [FW1]int g1/0/5 [FW1-GigabitEthernet1/0/5]ip address 61.67.1.1 24 [FW1-GigabitEthernet1/0/5]qu [FW1]firewall zone name dx ...
iplinkhelp[TYPE] DESCRIPTION iplinkadd-addvirtuallinklinkDEVICEspecifies the physical device to act operate on.NAMEspecifies the name of the new virtual device.TYPEspecifies the type of the new device. Link types:bridge- Ethernet Bridge devicebond- Bonding devicecan- Controller Area Network interfac...
interface:网路卡介面代号,包括eth0, eth1, ppp0 等等 options :可以接的参数,包括如下: up, down :启动(up) 或关闭(down) 该网路介面(不涉及任何参数) mtu :可以设定不同的MTU 数值,例如mtu 1500 (单位为byte) netmask :就是子遮罩网路;