To specify which protocols and ports the router forwards when forwarding broadcast packets, use the ip forward-protocol global configuration command. To remove a protocol or port, use thenoform of this command. ip forward-protocol{udp [port] | nd |sdns} noip forward-protocol{udp [port] | nd...
意思就是允许udp广播 nd的转发 nd Sun's Network Disk protocol (Sun的网络磁盘协议)
forward protocol udp 67(active)! ip helper-address 192.168.1.8 说明:dhcp来源于bootp(主机引导协议),它是主机在boot时靠udp广播来获取ip地址。使用ip forward-protocol udp bootps(bootpc)是因为dhcp的服务和客户分别用udp的67与68地址来分配和获取IP地址的。其实上述命令等同于ip forward-pro udp 67(68)。
Boot Protocol (BootP) client and server datagrams (port 67) TACACS service (port 49) 为了转发其他端口的UDP广播,用ip forward-protocol udp命令, 电脑资料 《CISCO学习问题之ipforwardprotocol命令的用法。网络知识》(https://www.unjs.com)。 如果只想转发BOOTP广播,则应该用no ip forward-protocol udp命令...
8位协议(protocol)用来区分上层协议。/etc/protocls文件定义了所有上层协议对应的protocol字段数值。其中,ICMP=1,TCP=6,UDP=17。/etc/protocols文件时RFC1700的一个子集。 16位头部校验和(header checksum)由发送端填充,接收端对其使用CRC算法以检验IP数据报头部(注意,仅检验头部)在传输过程中是否损坏。
意思就是允许udp广播 nd的转发 nd Sun's Network Disk protocol (Sun的网络磁盘协议)...
10、可以转发nd协议并关闭http ip forward-protocol nd no ip http server 如上是思科交换机的配置 对于华三转发nd协议是哪条命令 组网及组网描述: 2020-03-27提问 举报 (0) 最佳答案 24号扣子 默认透传。 2020-03-27回答 评论(2) 举报 (0) 是的 24号扣子 发表时间:2020-03-27 更多>...
ip forward-protocol nd ! ipv6 router ospf 10 router-id 1.1.1.1!--- Router ID of the route reflector router A!log-adjacency-changes ! end RRClient1 hostname RR-Client1 ! ip cef ! ipv6 unicast-routing ! interface Loopback0 no ip address ...
ip forward-protocol nd ! ipv6 router ospf 10 router-id 3.3.3.3 log-adjacency-changes ! end 验证 使用本部分可确认配置能否正常运行。 命令输出解释程序(仅限注册用户)(OIT) 支持某些 show 命令。使用 OIT 可查看对 show 命令输出的分析。 以下show命令用于验证配置: ...
1.1.11 ip forward-broadcast ip forward-broadcast命令用来配置允许接口接收和转发直连网段的定向广播报文。 undo ip forward-broadcast命令用来禁止接口接收和转发直连网段的定向广播报文。 【命令】 ip forward-broadcast undo ip forward-broadcast 【缺省情况】 设备禁止转发直连网段的定向广播报文;设备允许接收直连网段...