extern void VECSTART(void); Uint32 cpuCycleCount = 0; Uint32 sysClk; volatile Uint16 hitIsr = 0; int adc_out[65]=0,Tx_data_lsb,Tx_data_msb,i=0,j,count=0,count_int; int ADC_data[1300]; int adc_single_data=0; char *str={"\n ADC data :"}; char ...
interrupt void USER1_ISR(void) Other Parts Discussed in Thread:CONTROLSUITE InitAdc(); 进入这个函数后运行ADC延迟函数 DELAY_US(ADC_usDELAY); 延迟函数为: .def _DSP28x_usDelay .sect "ramfuncs" .global __DSP28x_usDelay_DSP28x_usDelay: SUB ACC,#1 ///从这个位置跳...
interrupt void CPU_timer_isr(void) 100k的中斷速度 interrupt void epwm1_timer_isr(void) 100k的中斷速度 interrupt void epwm4_timer_isr(void) 5k的中斷速度 interrupt void SCI_RX_isr(void) 目前沒有資料進來所以不會觸發中斷 而且我將以下的程式都放到RAM去執行 #pragma CODE_SECTION(CPU_timer_isr,"ra...
I need to know what that may do as interrupt i'm trying to convert an external analoge signal by ADC then filter it and then make DAC on the filtered signal double ADC0_Value ; void ADC0_ISR (void) interrupt 15 { ADC0_Value = ADC0 ; // Store ADC result in variable AD0INT =...
void __attribute__ ((interrupt(ADC12_VECTOR))) ADC12ISR (void) #else #error Compiler not supported! #endif { _DINT(); switch(__even_in_range(ADC12IV, ADC12IV_ADC12RDYIFG)) { case ADC12IV_NONE: break; // Vector 0: No interrupt ...
• void SysTick_Handler(void)是什么程序? 10296 提交评论 3 个讨论 1 ADC初始化源文件中有注明,如果程序从Flash运行, 需要在程序调用InitSysCtrl()函数之前将ramfuncs copy到片内RAM。 2018-11-28 15:43:16 评论 举报 1# 李秋年 提交评论 0 szoldman 发表于 2018-11-28 16:30 ADC...
void _ISR _T1Interrupt (void) { // interrupt service routine code here… } // _InterruptVector From Table 5.1, taken from the PIC24FJ128GA010 family datasheet, you can see which events can be used to trigger an interrupt. Table 5.1. Interrupt vector table of the PIC24F GA0 family ...
void loop(){ delay(delayTime); digitalWrite(LED,HIGH); delay(delayTime); digitalWrite(LED,LOW); } /// // Interrupt Service Routine// Do not use this ISR in 'real' code because // of switch bouncing see this page for useful// code:// https://www.best-microcontroller-projects.com/...
void _ISR _T1Interrupt (void) { // interrupt service routine code here… } // _InterruptVector From Table 5.1, taken from the PIC24FJ128GA010 family datasheet, you can see which events can be used to trigger an interrupt. Table 5.1. Interrupt vector table of the PIC24F GA0 family ...
void interrupt rtc_isr(void){ PTDD_PTDD3 ^= 1; RTCSC_RTIF = 1; /* Clear RTC interrupt */ } void interrupt pdb1_isr(void){ if(PDB1SCR_COF == 1){ PDB1SCR_COF = 1; if(PDB1CTRL2_CONT) { if(++pdb1_cont_times >= 5) { PDB1CTRL2_CONT = 0; //Disable continuous mode...