2: ens33: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:50:56:28:2c:xx brd ff:ff:ff:ff:ff:ff inet 192.168.xxx.xxx/24 brd 192.168.xxx.255 scope global dynamic ens33 valid_lft 1169sec preferred_lft 1169sec 3: virbr0: <NO-CARRIER,...
overrun mcast 0 0 0 0 0 0 TX: bytes packets errors dropped carrier collsns 0 0 0 0 0 0 2: venet0: <BROADCAST,POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT link/void RX: bytes packets errors...
下面是 ifconfig 命令输出的一些主要部分的解释: 接口名称:输出的第一列显示了网络接口的名称,如 eth0(以太网接口)或 wlan0(无线接口)。 标志(Flags):这一列显示了接口的状态和配置信息,如 UP(接口已启动)、BROADCAST(广播地址)、MULTICAST(多播地址)等。还有一些其他标志,如 LOOPBACK(回环接口)和 LOWER_UP(...
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000 link/ether bc:ee:7b:5e:7d:d8 brd ff:ff:ff:ff:ff:ff 3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 08:71:90...
2: venet0: <BROADCAST,POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT link/void 或者使用:ip -s link [root@linuxprobe ~]#ip -s link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN mode DEFAULT link/loopback 00:00:00:00:00:00...
# 1. 我的机器也确实出现了顺序不一样的情况[root@k8s ~]# ip a1: lo: <LOOPBACK,UP,LOWER_U...
2: ens33: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:25:62:6f brd ff:ff:ff:ff:ff:ff 配置网络接口 通过使用以下命令来打开或关闭网络接口: ip link set ens33 up ...
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000link/ether 04:01:13:8a:a2:01 brd ff:ff:ff:ff:ff:ffRX: bytes packets errors dropped overrun mcast853144 14672 0 0 0 0TX: bytes packets errors dropped carrier collsns91257 537 0 0 0 0 ...
要查看网卡细节：ip addr[root@linuxprobe ~]#ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferre...
在 CentOS 中,您可以按下 Ctrl + Alt + T 快捷键来打开一个新的终端窗口。 查看所有网络接口:要查看系统上的所有网络接口及其相关信息,请在终端中输入以下命令: ifconfig 复制代码 这将显示类似于以下内容的信息: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default...