System fails to boot with this error message:ifconfig: bad address. When coming up to multi-userifconfig -a, it indicates the following: le0: flags=863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500 inet 0.0.0.0 netmask 0 Once up, if this command succeeds, then all is well: # if...
We have to get up at 7:15 tomorrow morning, ___ we will be late for the 7:40 train. A. before B. or C. if D. so 查看完整题目与答案 He took the Mp3 player with him he could enjoy music during the trip. A. because B. so that C. when D. how 查看完整题目与...
I am getting a bad address error # ifconfig wl0.1 192.168.51.1/24 ifconfig: bad address '192.168.51.1/24' Is there a limitation as to what the address can...
大小写必须严格一致。我强迫症不小心改成了020B4000, 导致和dtsi中节点名称不一致,找不到设备,smsc_phy_reset直接退出了。 修改后,ifconfig eth0 up已恢复正常。 正点原子DS100手持Mini示波器发布,50M带宽,250M采样,双通道设计,美观大方,每个工程师都能用到. 回复 使用道具 举报 ...
example% ifconfig eri0 addif 192.168.200.1/24 up在eri0 物理接口上分配下一个可用的逻辑单元号,并分配 address 和prefix_length。可使用不同于关联物理接口的参数(address、prefix_length 等)来配置逻辑接口。也可以为与同一物理接口关联的多个逻辑接口指定不同的参数。每个逻辑接口都必须与一个现有的启动状态...
[gemini@localhost ~]$ systemctl status network.service ● network.service - LSB: Bring up/down networking Loaded: loaded (/etc/rc.d/init.d/network; bad; vendor preset: disabled) Active: active (exited) since Tue 2024-12-17 17:47:26 PST; 15min ago Docs: man:systemd-sysv-generator(8...
0 bad segments received.3208 resets sent Udp:114396 packets received 97 packets to unknown port received.0 packet receive errors 1277 packets sent TcpExt:9 ICMP packets dropped because they were out-of-window 12223 TCP sockets finished time wait in fast timer 82624884 delayed acks ...
可以看到,ifconfig up其实就是通过ioctl命令将该网卡标记上 IFF_UP 和 IFF_RUNNING,ifconfig down就是清除IFF_UP标记。set_flag()和 clr_flag()都是先通过 SIOCGIFFLAGS ioctl命令获取网卡当前的标记,修改后,再通过 SIOCSIFFLAGS命令设置回网卡驱动。这些ioctl命令定义于Kernel源码 include/uapi/linux/sockios.h ...
//ifconfig eth0 192.168.1.100 up /* skip argv[0] */ ++argv; //跳过 ifconfig #if ENABLE_FEATURE_IFCONFIG_STATUS //表示的命令是: ifconfig -a,下面的argv[0]=-a 表示列举所有的接口设备(eth0 usb0) if (argv[0] && (argv[0][0] == '-' && argv[0][1] == 'a' && !argv[0]...
AddressLessIf Indicates the index of the interface. ProcessId Indicates the process ID. RouterId Indicates the ID of the local router. PacketSrc Indicates the source IP address of the packet. ConfigErrorType Indicates the error type. 1: Bad Version 2: Area Mismatch 3: Unknown Nb...