-b,--nblock non-block mode (very early process wakeup) -S,--sync sync mode(0=none,1=simple,2=captshift,3=playshift,4=samplerate, 5=auto) -a,--slave stream parameters slave mode (0=auto, 1=on, 2=off) -T,--thread thread number (-1 = create unique) -m,--mixer redirect mix...
(2) I2S_Standard:通信标准格式选择,可选I2S Philips标准、左对齐标准、右对齐标准、PCM短帧标准或PCM长帧标准,它设定SPI_I2SCFGR寄存器I2SSTD位和PCMSYNC位的值。一般设置为I2S Philips标准即可。 (3) I2S_DataFormat:数据格式选择,设定有效数据长度和帧长度,可选标准16bit格式、扩展16bit(32bit帧长度)格式、 ...
NULL);if(!snd_proc_root->p)gotoerror;#ifdefCONFIG_SND_OSSEMULsnd_oss_root = create_subdir(THIS_MODULE,"oss");if(!snd_oss_root)gotoerror;#endif#ifIS_ENABLED(CONFIG_SND_SEQUENCER)snd_seq_root = create_subdir(THIS_MODULE,"seq");if(!snd_seq_root)gotoerror...
error = kobject_add(&dev->kobj, dev->kobj.parent, NULL); if (error) { glue_dir = get_glue_dir(dev); goto Error; } /* notify platform of device entry */ error = device_platform_notify(dev, KOBJ_ADD); if (error) goto platform_error; error = device_create_file(dev, &dev_attr...
(2) I2S_Standard:通信标准格式选择,可选I2S Philips标准、左对齐标准、右对齐标准、PCM短帧标准或PCM长帧标准,它设定SPI_I2SCFGR寄存器I2SSTD位和PCMSYNC位的值。一般设置为I2S Philips标准即可。 (3) I2S_DataFormat:数据格式选择,设定有效数据长度和帧长度,可选标准16bit格式、扩展16bit(32bit帧长度)格式、 ...
dev_name(dev)) { error = -EINVAL; goto name_error; } pr_debug("device: '%s': %s\n", dev_name(dev), __func__); parent = get_device(dev->parent); kobj = get_device_parent(dev, parent); if (IS_ERR(kobj)) { error = PTR_ERR(kobj); goto parent_error; } if (kobj) dev...
ESP_ERROR_CHECK(ret); play_i2s_init();//初始化I2S播放//audio_play(1);//播放第一个文件xTaskCreate(usart0_rx_task,"usart0_rx_task",1024*5,NULL, configMAX_PRIORITIES,NULL);//创建串口监听任务#ifdefDEBUG//play_spiffs_name("all.wav");//播放all.wavfor(intj=0;j<21;j++){ ...
error: snd_info_free_entry(snd_proc_root); return-ENOMEM; } 查看时钟clk summary 查询音频时钟,确认时钟设置正确 示例:查询 i2s0 mclk 频率,以及其所在的 pll,结果:mclk 为 12288000 Hz,pll 源为 cpll cat /sys/kernel/debug/clk/clk_summary | egrep"i2s0|pll" ...
开始接收数据时,先运行 i2s_run() ,等待 VSYNC 信号变为高时,即表示摄像头端已经开始一帧图像传输,需要跳过 VSYNC 为低时的数据,再采集过程中出现 VSYNC 由高到低变化,则表示一帧图像传输完成,VSYNC 中断服务函数 vsync_isr 当前DMA 接收链表描述符被处理完成时将触发 I2S_IN_DONE_INT 中断,进入 i2s_...
* device and the driver sync_state callback is called for this device. */ if (dev->fwnode && !dev->fwnode->dev) { dev->fwnode->dev = dev; fw_devlink_link_device(dev); } bus_probe_device(dev); if (parent) klist_add_tail(&dev->p->knode_parent, ...