int32_t i2s_buffer[I2S_BUF_SIZE * 2]; //左声道和右声道最大振幅 int16_t max_left_amplitude = INT16_MIN; int16_t max_right_amplitude = INT16_MIN; void setup() { Serial.begin(9600); //配置I2S接口 i2s_config_t i2s_config = { ...
i2s_config_t i2s_config = { .mode = I2S_MODE_MASTER | I2S_MODE_TX, .sample_rate = 44100, .bits_per_sample = I2S_BITS_PER_SAMPLE_32BIT, .channel_format = I2S_CHANNEL_FMT_MULTIPLE, // 启用多通道 .communication_format = I2S_COMM_FORMAT_STAND_I2S, .dma_buf_count = 8, .dma_buf_...
然后,初始化给定 I2C 端口的配置,请使用端口号和 i2c_config_t 作为函数调用参数来调用 i2c_param_config() 函数。 配置主机: AI检测代码解析 int i2c_master_port = 0; i2c_config_t conf = { .mode = I2C_MODE_MASTER, // 设置 I2C 接口为主机模式 .sda_io_num = I2C_MASTER_SDA_IO, // 选择...
ESP_RETURN_ON_ERROR(i2c_param_config(I2C_NUM, &es_i2c_cfg), TAG, "config i2c failed"); ESP_RETURN_ON_ERROR(i2c_driver_install(I2C_NUM, I2C_MODE_MASTER, 0, 0, 0), TAG, "install i2c driver failed"); /* 初始化es8311芯片 */ es8311_handle_t es_handle = es8311_create(I2C_NUM,...
可以直接在const i2s_config_t device_i2s_config这里调整合适的参数就可以。 问题3:是否还有其他的方式设置I2S输入? 可以的,从LINE IN输入替换输入源,只是为了方便验证这个功能而已,如果大家为了做项目,要按照正常的逻辑来添加I2S输入的枚举,添加I2S链路。
snd_proc_root->p) goto error;#ifdef CONFIG_SND_OSSEMUL snd_oss_root = create_subdir(THIS_MODULE, "oss"); if (!snd_oss_root) goto error;#endif#if IS_ENABLED(CONFIG_SND_SEQUENCER) snd_seq_root = create_subdir(THIS_MODULE, "seq"); if (!snd_seq_root) goto error;#endif if (snd...
开启半双工传输许可, 即配置寄存器SPI_I2S_GCTL 中的 TXEN 或 RXEN 位为‘1’ (TXEN、 RXEN不可同时配置为‘1’)。 注意:从模式下发送时,在检测到WS的边沿之前,需要对寄存器SPI_I2S_TXREG进行1次数据写入操作;而且,从模式下接收时,在配置RXEN位为‘1’之前,需要一直维持WS输入信号在高电平。
1.struct bflb_i2c_config_s 说明:I2S 配置的结构体。 struct bflb_i2s_config_s { uint32_t bclk_freq_hz; uint8_t role; uint8_t format_mode; uint8_t channel_mode; uint8_t frame_width; uint8_t data_width; uint8_t fs_offset_cycle; ...
1.struct bflb_i2c_config_s 说明:I2S 配置的结构体。 struct bflb_i2s_config_s { uint32_t bclk_freq_hz; uint8_t role; uint8_t format_mode; uint8_t channel_mode; uint8_t frame_width; uint8_t data_width; uint8_t fs_offset_cycle; ...
esp_err_ti2s_set_pin(i2s_port_ti2s_num,consti2s_pin_config_t*pin) 这个函数有两个参数,第一个参数就是I2S的接口号,第二个参数是pin_config的结构体初始化,如果第二个结构体参数是NULL的话,就默认设置GPIO25&GPIO26引脚,也就是说内置的两个DAC都会被初始化; ...