i2cset是Linux下的一个命令行工具,用于向I2C设备写入数据。I2C(Inter-Integrated Circuit)是一种串行通信协议,用于在集成电路之间进行短距离通信。i2cset可以通过 I2C 总线与 I2C 设备进行通信,将指定的数据写入设备的特定寄存器。下面将详细介绍i2cset的用法。 1.命令结构和语法: 选项: -y:在写入前不再确认,默认情...
sudo i2cset [-y] [-f] [-m mask] [-r] I2CBUS CHIP-ADDRESS DATA-ADDRESS [VALUE] [MODE] 。 其中: -y代表跳过确认提示。 -f代表强制执行。 -m mask 代表掩码,可以指定特定位。 -r代表读取,不指定时默认是写操作。 I2CBUS 是I2C总线的地址,如/dev/i2c-0。 CHIP-ADDRESS是设备的I2C地址。 DATA...
usage: i2cdetect -F BUS usage: i2cdetect -l Detect i2c devices. -a All addresses (0x00-0x7f rather than 0x03-0x77) -F Show functionality -l List all buses -r Probe with SMBus Read Byte -y Answer "yes" to confirmation prompts (for script use) console:/ # i2cdetect -a i2cdetect...
i2cset [-f] [-y] [-m mask] [-r] [-a] i2cbus chip-address data-address [value] ... [mode] i2cset -V DESCRIPTION i2cset is a small helper program to set registers visible through the I2C bus. OPTIONS -V Display the version and exit. -f Force access to the device even if...
-f表示强制访问忙碌的设备,即使它们已经被内核驱动占用了。这个选项可能会导致一些设备的错误操作,所以要谨慎使用。 -y表示在执行读取之前不进行确认提示,这个选项适合脚本使用。 BUS表示要读取的I2C总线编号,如0, 1, 2等。 CHIP表示要读取的I2C设备地址,如0x20, 0x3c等。
i2cset [-f] [-y <bus>] [<value> ...] ``` 其中各选项的含义如下: - -f:强制操作,即使总线忙也继续执行。 - -y <bus>:指定I2C总线的编号,默认为1。 - : I2C设备地址,在十六进制表示法下指定。 - :寄存器地址,在十六进制表示法下指定。 - <value>:要写入寄存器的值,在十六进制表示法下指...
bash i2cset -f -y 0 0x2d 0x00 0x11 b 重新运行修改后的i2cset命令: 在修正了mode参数后,重新运行i2cset命令,观察是否还会出现“mode too long”的错误。 如果以上步骤仍然无法解决问题,你可以进一步查看i2cset的文档或寻求社区的帮助。确保你的i2c-tools是最新版本,并且你的系统配置正确无误。
Write an i2c register. MODE is b for byte, w for 16-bit word, i for I2C block. -f Force access to busy devices -y Answer "yes" to confirmation prompts (for script use) 9. 设置设备指定寄存器地址的值 rk3568_r:/ # i2cset -fy 0 0x20 0x12 0x04 b...
i2cset -f -y 0 0x21 <Command> <Data> i2cget -f -y 0 0x21 <Command> But from the datasheet of TCA6424A, it specifies Slave address as a field in the Write or Read sequence as shown below: Where to include this Slave address in the i2cset/i2cget commands? Could you ...
i2cset -y 2 0x40 0x00 0xFB0F w、忽略高4位。 该寄存 器读回 FB6F、在字节交换后为6FFB、该值= 01101111111111111011、即我最初打算使用的触发、长采样、最大采样平均配置的精确配置。 因此、您的配置寄存 器的解决方案似乎只是设置位0-11、最高有效字节 MSB、首先。