hardware is powered directly from the PC’s USB port, and there’s no need to install device drivers since it uses standard USB HID drivers already installed in Windows. This will allow you to get started quickly with the intuitive and flexible software that it included with USB-to-I2C ...
Manuals, Downloads and Updates for I2C Tools can be found here. Please click on these links for a quick answer to your questions!
言归正传 不少人也体验过嵌入式开发板linux上的i2c-tools工具,能够扫描i2c总线上的设备,查看指定设备的寄存器,这样的工具要是windows上也有就好了,调试一些传感器或者摄像头SCCB之类的就不用在找开发板来做了。串口是很多搞嵌入式开发的必备工具,如果身边的随手可见的串口突然也可以调试i2c,spi了会不会感觉瞬间美滋滋?
1. 从 Windows 的启动菜单中打开 Bridge Control Panel. 它位于赛普拉斯文件夹中. 2. 选择器件列表中的 MiniProg3 或 CY3240 , 并点击 Connect(连接)按键. 3. 随后,点击 Power(电源)按键,实现为 CY3210 测 试设置供电.(请参见图 29.) 电源键 连接键 4. 为了写入 LED 和 DAC 参数,在 Bridge Control...
<i2c_addr> I2C slave address. <addr> Address (of length addr_width) inside I2C target device to read/write operation. Note that the <addr> value is ignored if <addr_witdh> = 0. <data> Data (bytes of length data_width) to write to target device. ...
TX2 i2c-tools使用 安装: apt-get install libi2c-dev i2c-tools 回到目录 检测i2c总线数目 用i2cdetect检测有几组i2c总线在系统上: i2cdetect -l 可以看到系统中有9组IIC。 回到目录 检测i2c总线上挂载的设备 用i2cdetect检测挂载在i2c总线上器件: i2cdetect-r -y 1...
Windows 可参考开发资料:CH347EVT.ZIP - 南京沁恒微电子股份有限公司 【目录:CH347EVT\EVT\TOOLS\CH347Demo】 界面读示例如下: Linux例程 可参考代码,链接地址:CH341PAR_LINUX.ZIP - 南京沁恒微电子股份有限公司USB转JTAG/SPI/I2C/并口/GPIO等接口的Linux设备驱动程序,支持CH341的USB转SPI/I2C/EPP并口/MEM并口...
在C:\Program Files (x86)\Windows Kits\10\Tools\x64\ACPIVerify 中下载 WDK 并找到 asl.exe 运行以下命令以生成 ACPITABL.dat: ps 复制 asl.exe yourboard.asl 将生成的 ACPITABL.dat 文件复制到受测系统上的 c:\windows\system32。 在受测试的系统上启用 testsigning : ps 复制 bcdedit /set tes...
安装i2c-tools:sudo apt-get install i2c-tools 安装python-smbus:sudo apt-get install python-smbus 检测i2c设备:安装完工具和库后,可以使用命令行工具i2cdetect来检测已连接的i2c设备。运行命令sudo i2cdetect -y 1,将会显示已连接设备的地址。 编写i2c驱动程序:根据具体需求,可以使用各种编程语言编写i2c驱动程序...
To start mlxi2c: Start the mst driver (mst start or mst restart). Note: This step in not required in Windows. Run mlxi2c with the following command line syntax: # mlxi2c [switches...] [parameters...] Switches Options Commands Example...