i2c_flag_get(I2Cx, I2C_FLAG_BTC)) { if((I2C_Timeout--) == 0) { Resume_IIC(I2C_LONG_TIMEOUT,I2Cx); return I2C_FAIL; } } /* send a stop condition to I2C bus */ i2c_stop_on_bus(I2Cx); I2C_Timeout = I2C_SHORT_TIMEOUT; while (I2C_CTL0(I2Cx) & 0x0200) { if((I2C_...
<drivers/i2c/busses/i2c-designware-master.c> 635 static void i2c_dw_prepare_recovery(struct i2c_adapter *adap) 636 { 637 struct dw_i2c_dev *dev = i2c_get_adapdata(adap); 638 639 i2c_dw_disable(dev);/* disable了i2c controller */ 640 reset_control_assert(dev->rst); /* 复位了i2c...
https://community.nxp.com/t5/i-MX-Processors/I2C-reset/m-p/253182 Best regards igor 0件の賞賛 返信 12-22-202007:08 AM 8,503件の閲覧回数 mspenard603 Contributor IV Got it. You use I2C_MasterReset() which sets the software reboot bit in MCR. Which then clears Bus Busy bit in...
i2c_init|__i2c_first_dynamic_bus_num=of_alias_get_highest_id("i2c")+1|//__i2c_first_dynamic_bus_num表示动态分配的i2c bus num,为静态分配bus num最大值加1|bus_register(&i2c_bus_type)|is_registered=true//表示 driver model 已经初始化完成|i2c_add_driver(&dummy_driver) i2c_init主要的工...
类似的,SMBus对接口被重置(Reset)后的恢复时间(Timeout)也有要求,一般而言是35mS,I2C这方面亦无约束,可以任意延长时间。相同的SMBus也要求无论是在主控端(Master)或受控端(Slave),其频率处于Lo电平时的最长持续时间不得超越限制,以免因为长时间处在Lo准位,而致收发两端时序脱轨(失去同步,造成后续误动作)。
(If the master drives a high, but sees a low, so it lost arbitration)The solution is to set the port bits to output and drive them high before setting up the I2C port: Code: void InitI2C(void){ // This will unhang the I2C module if reset while sending DDRJ |= 0xc0; // make...
echo 0 > /sys/class/i2c-adapter/i2c-1/reset # 替换1为你的I2C总线号 6. 修改内核参数 在某些情况下,调整内核参数可以帮助避免死锁。 编辑/etc/sysctl.conf文件,添加以下行: 代码语言:txt 复制 kernel.i2c.masterslave = 0 kernel.i2c.lockup_timeout = 1000 ...
这是因为SMBus面向电脑中很多可拆卸设备,必须确定该设备是否存在,避免误操作。SMBus还加入了WatchDog,在SMBCLK拉低后,不得超过35ms(这就是10KHz的最低频率的由来),否则Slave应该Reset。而I2C并没有该限制。这让SMBus避免了复杂的错误恢复电路。SMBus还提供了单独的SMBSUS来用于Slave向Master报警。
有power 控制和 reset 控制的 slave。 other slave。 复现问题后,可以手动将相应外设去掉,确认是哪个外设将 i2c bus 拉住,再与供应商沟通,debug 一下该 IC 状态,理清拉住 i2c bus 原因。 三、i2c-tools i2c-tools 也很好用,这个工具工具博主上次写过,参考以下文章: ...
这是因为SMBus面向电脑中很多可拆卸设备,必须确定该设备是否存在,避免误操作。SMBus还加入了WatchDog,在SMBCLK拉低后,不得超过35ms(这就是10KHz的最低频率的由来),否则Slave应该Reset。而I2C并没有该限制。这让SMBus避免了复杂的错误恢复电路。SMBus还提供了单独的SMBSUS来用于Slave向Master报警。