I can't see any particular settings for this in the DTS. 1. Where is the configuration for this I2C type of device ? 2. Has anyone seen this issue before ? 3. Any ideas ? Solved! Go to Solution.0 Kudos Reply 1 Solution 03-07-2024 10:56 PM 1,435 Views TerryBarnaby...
请教一下,在9221的手册programming一节,分别包含configuration和slave i2c interface两部分,其中config介绍了三种模式,那么请问,configuration和i2c这两种是并列的两种给9221配置的方式吗? 可否理解为,config是通过上电的时候将firmware这个文件下载到9221芯片使其完成初始化配置,然后正常工作。而i2c则是通过其他host比如fpga在...
I2C_ClockSpeed = I2C1_CLOCK_FRQ; /* I2C Peripheral Enable */ I2C_Cmd(I2C1, ENABLE); /* Apply I2C configuration after enabling it */ I2C_Init(I2C1, &I2C_InitStructure); I2C_ITConfig(I2C1, I2C_IT_EVT, ENABLE); //Part of the STM32 I2C driver I2C_ITConfig(I2C1, I2C_IT_BUF, ...
Hi, I'm using NTAG I2C chip NT3H2111 for one of my projects, i would like to enable the NFC SILENCE Feature. So, i changed the configuration register
手册中已经描述,该模块默认工作在从模式,要想变为主模式,主要生产一个起始条件。(主模式的代码可以参考野火开发板的硬件i2c历程,本例子中也是使用野火开发板硬件i2c作为主机的) 二、i2c从机的配置 I2C_DeInit(I2C1); /* I2C1 configuration ---*/ I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;//模式 I2C_In...
在Pinout & Configuration选项卡中,选择需要使用的I2C接口(如I2C1)。 自动分配SCL和SDA引脚,或者手动选择你需要的引脚。 配置I2C参数: 点击Configuration选项卡,选择I2C1 Configuration。 设置I2C模式(如I2C Master),时钟速度(如100kHz),以及其它需要的参数。
(TAG, "i2c configuration failed. code: 0x%.2X", espRc); } i2c_cmd_link_delete(cmd); vTaskDelay(5 / portTICK_PERIOD_MS); // wait to complete the write cycle } uint8_t readEEPROM(uint16_t address) { uint8_t data; i2c_cmd_handle_t cmd = i2c_cmd_link_create(); i2c_master...
在这个示例代码中,您需要根据实际情况配置系统时钟、GPIO引脚和I2C外设。I2C_Configuration()函数用于配置I2C外设并使用`HAL_I2C_Init()`进行初始化。而在主函数中,我们使用`HAL_I2C_Master_Transmit()`函数来发送数据,使用`HAL_I2C_Master_Receive()`函数来接收数据。
2. 在"Pinout & Configuration"选项卡中,选择一个可用的I2C接口和相应的引脚作为SDA和SCL线。 3. 在"Configuration"选项卡中,配置I2C的工作模式、时钟源、时钟速率等参数,以满足你的需求。 步骤二:初始化I2C接口和外设 以下是一个使用I2C接口与外设通信的示例代码(以I2C1为例): ...