Single master system do not have clock synchronization and bus arbitration, only I2C bus with more than 1 master need to consider this. As clock synchronization, as mentioned above, I2C is awake pull up/strong pull lowbus, also can be described as "wired AND" connection. So if there are ...
I2C总线上拉电阻对VOL的影响 如下图所示,在I2C主机发出低电平时,内部的MOSFET导通,导通电阻Rdson与I2C总线上拉电阻Rpullup组成电阻网络。根据戴维南定理,如果上拉电阻Rpullup阻值越小,则Rdson上的电压VOL就越大。显然,如果VOL大于某一特定值,I2C从机就无法监测出I2C总线上的低电平。另外,如果上拉电...
电科星拓INTL9555/9554是具有中断输出的16路/8路I2C和SMBus GPIO扩展器。可为两线双向I2C总线(或SMBus)提供16位/8位通用并行输入和输出扩展,该器件的工作电源电压范围为1.65V至5.5V。器件功能包括当输入端口状态发生变化时,在INT引脚上生成中断。硬件可选地址引脚A0、A1和A2,最多允许8个该器件位于同一I2C总线上...
图9展示了从从机寄存器读取单个字节的例子。 这是对德州仪器的应用文档SLVA704的中文翻译,原文标题为:Understanding the I2C Bus。相比于飞利浦出品的几十页的I2C标准文档,此文档只有8页,但是对于想要了解标准I2C总线并应用的人来说,这个已经够用了。原文地址:https://www.ti.com/lit/an/slva704/slva704.pdf 声明...
上面第一张图已经解释了,I2C是有很多设备线与连接而成,如果采用push-pull的output buffer的话,难免会出现下面的情况,一个设备输出高,另外设备输出低,也就是左边设备的PMOS打开而右边设备的NMOS打开,这样就在VCC和GND之间形成短路,此时大的电流会把设备烧毁,后果是灾难性的。这种现象还有专门的英文名字叫bus contentio...
3. Open-drain bus lines require pullup resistors 4. Reduced noise immunity 主机和从机经由多条总线通过串行接口进行通讯。在写周期,主机使用自己产生的时钟和数据将数据传至从机。在读周期,从机传输数据至主机。 SPI、QSPI和MICROWIRE设计 由Motorola制定的SPI接口已被很多流行的处理器和微控制器采用,比如MAXQ20...
Initiate the Wire library and join the I2C bus as a master or slave. This should normally be called only once. Syntax语法 Wire.begin(address) Parameters参数 address: the 7-bit slave address (optional); if not specified, join the bus as a master. ...
Initiate the Wire library and join the I2C bus as a master or slave. This should normally be called only once. Syntax语法 Wire.begin(address) Parameters参数 address: the 7-bit slave address (optional); if not specified, join the bus as a master. ...
查《I2C-bus specification and user manual.pdf》表10: 从上图可以得到最大电阻和最小电阻计算公式以及如下数据: 1、标准模式:0~100KHz,上升沿时间要求 tr = 1us 2、快速模式:100~400KHz,上升沿时间要求 tr = 0.3us 3、高速模式:up to 3.4MHz,上升沿时间要求 tr = 0.12us ...
•Unidirectional bus: Ultra Fast-mode (UFm),5 Mbit/s 速度由 SCL 决定,不同模式对上升沿的要求不一样,上升沿斜率受上拉电阻和等效电容影响。 4、I2C 是一种多主从架构总线 I2C 的读写均由 master 端发起。 I2C 通信的每一个 byte(8bits)都需要 slaver 端的回应ACK/NACK 作为回应。