hub_ext_port_status failed (err = -110) Thread starter Indirectelex Start date Jul 4, 2023 Forums Proxmox Backup Server Proxmox Backup: Installation and configuration I IndirectelexMemberMay 26, 2021 95 11 13 35 Canada Jul 4, 2023 #1 Hi everyone, I wonder what this error message ...
[ 266.185680] hub 3-0:1.0: hub_ext_port_status failed (err = -32) [ 266.191597] usb usb3-port1: Cannot enable. Maybe the USB cable is bad? [ 266.265681] hub 3-0:1.0: hub_ext_port_status failed (err = -32) [ 266.477680] hub 3-0:1.0: hub_ext_port_status failed (err = -...
使用旧版boot.cmd时需要用extlinux/extlinux.conf才可以启动,armbianEnv.txt删除了也能启动。 使用新版boot.cmd时,只使用armbianEnv.txt也能启动,不需要extlinux/extlinux.conf。或者只使用extlinux/extlinux.conf,不使用armbianEnv.txt也能启动。两个都存在也可以启动。
157 3.8.12.3 UNCERRSTS[0] - Uncorrectable Error Status For ESI Port ... 158 3.8.12.4 UNCERRMSK[7:2] - Uncorrectable Error Mask ... 159 3.8.12.5 UNCERRMSK[0] - Uncorrectable Error Mask For ESI Port ... 159 3.8.12.6 UNCERRSEV[0] - Uncorrectable Error Severity For ESI Port ... ...
SDIO Port B: 0, SDIO Port C: 1 emmc/sd response timeout, cmd8, status=0x3ff2800 emmc/sd response timeout, cmd55, status=0x3ff2800 init_part() 293: PART_TYPE_AML [mmc_init] mmc init success dtb magic 00088b1f Amlogic multi-dtb tool ...
STATUS_NO_LOGON_SERVERS which triggers NTLM fallback. 3. Because NTLM fallback is blocked on MS16-101, Error STATUS_DOWNGRADE_DETECTED is returned to the calling app. Solution:Easy. Install the October update which will fix this issue. The fix lies inadsmse...
(not driven by MCH) 100 Hard Failure (not driven by MCH) 101 No data response 110 Implicit Writeback 111 Normal data response Processor 1 Response Status Parity: Processor Bus 1 Target Ready: This signal indicates that the target of the processor transaction is able to enter the data ...
FDT_ERR_BADMAGIC, load default parameters vpu: clk_level = 7 vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300) vpp: vpp_init MMC: aml_priv->desc_buf = 0x0000000033eddac0 aml_priv->desc_buf = 0x0000000033edfde0 SDIO Port B: 0, SDIO Port C: 1 emmc/sd response timeout,...
(not driven by MCH) 100 Hard Failure (not driven by MCH) 101 No data response 110 Implicit Writeback 111 Normal data response Processor 1 Response Status Parity: Processor Bus 1 Target Ready: This signal indicates that the target of the processor transaction is able to enter the dat...
: -110 Card did not respond to voltage select! : -110 switch to partitions #0, OK mmc2(part 0) is current device Scanning mmc 2:1... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 397 bytes read in 1 ms (387.7 KiB/s) 1: Armbian Retrieving file: /u...