If none of the resolutions helped you to Fix HP Printer Fuser Error 50.2. Finally, you require to purchase the new Fuser kit. To settle the problem you need to connect with specialists of the HP printer support team before buying. There may be a possibility you don't require to purchase ...
Printer mispick(打印机拾纸错误) 打印引擎未能拾取一张纸。 将纸张重新装入进纸盘,然后按下执行按钮继续作业。 如果消息仍然存在,请与 HP 支持部门联系。 Printing(正在打印) 产品正在打印文档。 请耐心等待,直至打印完成。 安装黑色碳粉盒 尚未在产品中安装碳粉盒,或者安装不正确。
A 'Fuser Error' message displays on the computer screen, and the printer does not print. Solution one: Reset the printer Follow these steps to reset the printer. Press the Power button to turn off the printer. Disconnect the power cord from the rear of the printer. Wait 30 seconds, and ...
9、印机的风扇是否被正确的接入以及是否被阻碍物卡住;2.更换风扇59.* PRINTER ERROR 马达错误,*值表示如下:0 马达错误1 马达启动错误2 马达运转错误 1.重新启动打印机;2.确定各连接齿轮能正常运转;3.确定连接马达的电缆被正确插入4.更换马达 62.* PRINTER ERROR 打印机内存错误,*值表示如下:0=内部内存1-3=...
FUSER ERROR 加热组件错误,其*值表示如下: 1 加热温度偏低 2 加热组件预热保护 3 加热温度偏高 4 电源电压不稳 5 加热组件不匹配 1. 关掉电源,20分钟后再开机; 2. 重新安装加热组件; 3. 关掉电源,取出加热组件,检查J1307-1和J1307-2以及J1308-1和J1308-2是否相通,如不通,更换另热组件 51.* PRINTER...
53.13.YY PRINTER ERROR TO CONTINUE 38、PRESS CANCEL JOB 打印机控制面板可能显示的错误消息: 说明 出现 DIMM 插槽 J3 (如格式器板上的标签所示) 中的打印机内存错误。 该内存可能不受支持。 措施 1. 按 Cancel Job 按钮。 2. 关闭打印机,然后将其重新启动。 3. 如果该消息仍然存在,则检查插槽 J3 中...
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits curre...
55 PRINTER ERROR 内部通讯错误 1.检查电源位置 2.更换接口板 3.更换DC控制板 56 * PRINTER ERROR临时打印错误,*值表示: 1.不正确的输入或错误的附加设备被连接 2.不正确的输出 1.重新启动打印机; 2.检查打印机的配置; 3.校正连接的附加设备
HP Printer Errors [vc_row type=”container”][vc_column][vc_column_text] How To Fix HP Printer Technical Errors HP Printer Error Support Number, HP Printer Installation Error Support Number, HP Technical Error Support Number, HP Printer Paper Jam Error Support Number...
* PRINTER ERROR is the laser scanning speed mismatch. * value is shown as follows: 1 scan startup error 2 scan rotation error Method: 1 restart; 2 re-install the laser and connected cable; 3 replace laser 53. XY. ZZPRINTER ERROR is an additional memory ERROR, where the meaning of XYZ...