During a print job, the carriage stalls, the printer stops, and the following error message displays on the printer control panel: The print carriage cannot move. Open the ink cartridge access door, clear any paper jam or obstruction, and select OK. Try the following solutions to resolve the...
During a print job, the ink cartridge carriage stalls in the printer, and a Carriage Jam or E3 error displays on the printer control panel. Fix a carriage jam or E3 error | HP printers Learn how to fix a carriage jam or E3 error on your HP printer by following the steps in this v...
Check out our Black or Color Ink Not Printing, Other Print Quality Issues info about: Print quality and Cartridge Issues. It has been a while since anyone has replied. Simply ask a new question if you would like to start the discussion again.Su...
纸路传感器异常。主要是由于光敏反射式传感器上的积尘太多或二极管损坏、光敏三极管损坏、传感器电路故障所致。其维修方法如下：1、检查纸张检测传感器上是否积灰太多，以致影响了光敏三极管接收发光二极管的光束。如果纸张检测传感器上有很多积尘，需要将其清理。2、如果纸张检测传感器上没有积尘，接着检测光敏...
你仔细的找下 刚刚纸拔出来的位置，可能你把那个感应纸的传感器弄了下没有弹回去 用手弄下就好了 HP 的感应器一般都是黑色的很小的传感器用手碰下都会动的里面有个小弹簧钩上的。应该就是在硒鼓下面
Check Ink Cartridge Installation: Ensure that the cartridges are installed correctly and are seated properly in their slots. Sometimes, even a slightly misaligned cartridge can trigger an error. Clean the Contacts: Gently clean the metal contacts on the cartridges and...
推荐答案 纸路传感器异常。主要是由于光敏反射式传感器上的积尘太多或二极管损坏、光敏专三极管损坏、传属感器电路故障所致。其维修方法如下: 1、检查纸张检测传感器上是否积灰太多,以致影响了光敏三极管接收发光二极管的光束。如果纸张检测传感器上有很多积尘,需要将其清理。 2、如果纸张检测传感器上没有积尘,接着检测...
惠普HP LaserJet M1005 MFP开机提示 jam in print paper path修复后,又提示door open,又修复后,又提示no print cartridge。搞了好几个小时,终于修好了。#打印机维修 #专业维 - 余姚市万维维修中心于20231014发布在抖音,已经收获了103个喜欢,来抖音,记录美好生活!
cartridge area 可以替换 Clear jam and then press碳粉盒区域发生卡纸。打开挡门,清除卡纸,然后按下控制面板上的 (选择)按钮。 Jam in ouput bin 可以替换 Clear jam and then press出纸槽发生卡纸。打开挡门,清除卡纸,然后按下控制面板上的 (选择)按钮。
Jam incartridgearea The product has detected a paper jam inthe print cartridgearea. 1.Clear the jam from the areaindicated in the message, and then follow the control panelinstructions. 2.If the error persists, clean the fuser inlet guide. If the inlet guide is scratched, replace thefuser....