比如: hostapd_cli -i wlan0 -p /data/vendor/wifi/wpa/sockets,那么这里ctrl_interface就要变为/data/vendor/wifi/wpa/sockets才能让hostapd_cli顺利调用。 5. ctrl_interface_group=wheel ---ctrl_interface_group类似ctrl_interface,由多用户组成的组来控制hostapd。 6. ssid=AP_TEST ---ssid的值就是热点名...
这是一个hostapd配置文件的示例,适用于设置一个 Wi-Fi 接入点。下面是该配置文件中各项参数的说明: ctrl_interface=/var/run/hostapd:指定控制接口的位置,hostapd可以通过该接口与其他进程进行通信。 ctrl_interface_group=0:设置控制接口的用户组,这里为 0(通常指 root)。 interface=wlan0:定义要用作接入点的无线...
interface=wlp2s0 #bridge=br0 driver=nl80211 logger_syslog=-1 logger_syslog_level=2 logger_stdout=-1 logger_stdout_level=2 #ctrl_interface=/var/run/hostapd #ctrl_interface_group=wheel #ctrl_interface_group=0 ### IEEE 802.11 related configuration ### ssid=test #ssid2=mytest #ssid2=P"hel...
再在单板上vi一个hostapd.conf: interface=wlan0 driver=nl80211 ctrl_interface_group=0 hw_mode=g max_num_sta=2 ssid=ap_wifi auth_algs=1 channel=1 country_code=CN ieee80211d=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_passphrase=12345678 wpa_pairwise=CCMP own_ip_addr=192.168.25.1 至此hostapd全部...
ctrl_interface=/var/run/hostapdctrl_interface_group=wheel# Some usable default settings...macaddr_acl=0auth_algs=1ignore_broadcast_ssid=0# Uncomment these for base WPA & WPA2 support with a pre-shared keywpa=2wpa_key_mgmt=WPA-PSKwpa_pairwise=TKIPrsn_pairwise=CCMP# DO NOT FORGET TO SET...
#ctrl_interface_group=wheel #ctrl_interface_group=0### IEEE802.11related configuration ### ssid=test #ssid2=mytest #ssid2=P"hello\nthere"utf8_ssid=1# ISO/IEC3166-1标准的国家代码,用于设置监管域。根据需要设置,按照哪个国家来操作设备。 # 这可以限制可用的频道和发射功率。 #country_code=CN #...
#ctrl_interface=/var/run/hostapd #ctrl_interface_group=wheel #ctrl_interface_group=0 ### IEEE 802.11 related configuration ### ssid=test #ssid2=mytest #ssid2=P"hello\nthere" utf8_ssid=1 # ISO/IEC 3166-1 标准的国家代码,用于设置
iface[i]) || hostapd_setup_interface(interfaces.iface[i])) //将配置文件通过写入驱动 goto out; } hostapd_global_ctrl_iface_init(&interfaces); if (hostapd_global_run(&interfaces, daemonize, pid_file)) { wpa_printf(MSG_ERROR, "Failed to start eloop"); goto out; } ret = 0; out: ...
-C = ctrl_interface parameter (only usedif-cisnot)-d = increase debugging verbosity (-dd even more)-D =driver name (can be multiple drivers: nl80211,wext)-e =entropy file-f =log output to debug file instead of stdout-g =globalctrl_interface-G =globalctrl_interface group-h = show...
ctrl_interface=/var/run/hostapd # Access control for the control interface can be configured by setting the # directory to allow only members of a group to use sockets. This way, it is # possible to run hostapd as root (since it needs to change network ...