state = Serial.read(); // Reads the data from the serial port } // Controlling the LED if (state == '1') { digitalWrite(ledPin, HIGH); // LED ON state = 0; } else if (state == '0') { digitalWrite(ledPin, LOW); // LED ON state = 0; } // Reading the potentiometer p...
HC-05 bluetooth module(with en pin and state pin) 电阻1个 二极管小灯1个 杜邦线若干 andriod手机(APP:蓝牙串口) 蓝牙串口app 连接电路 hc-05_test_with_light.png arduino code #include<SoftwareSerial.h>#defineAnalogPin 9charch=' ';//用来存储手机发送过来的数据SoftwareSerialBT(3,2);//RX TX o...
让HC-05模组进入AT模式,需要在通电之前,先把KEY引脚(蓝牙模组本身的34脚)接在高电位(通常3.3v,但是接5v也行),如果,只要一通电蓝牙模组就进入AT模式 在尚未与其他蓝牙装置配对之前,HC-05板子上的LED将每秒闪烁1次。若进入AT模式,LED将每两秒闪烁一次,HC-05的AT命令,采用38400bps的速率传送 笔者购买的HC-05板...
蓝牙模块HC-05使用说明 一、HC-05模块简介 HC-05是一款主从一体的蓝牙串口模块,工作频段为24GHz,具有低功耗、传输稳定等特点。它支持蓝牙20协议,可以与各种带有蓝牙功能的设备进行通信,如手机、平板电脑、电脑等。 该模块有6个引脚,分别为VCC(电源正极)、GND(电源负极)、TXD(发送数据)、RXD(接收数据)、STATE(...
工作电压范围为4V 至 6V(通常为 +5V),工作电流为30 mA。模块的范围是 100 米。HC-05 蓝牙模块共有 6 个引脚,其中 EN 和 State 引脚用于命令模式。HC-05蓝牙模块的管脚如下图所示: 电路原理图 将HC-05 蓝牙模块与 TI-MSP340 板连接的电路图如下所示。
HC05 USB至TTL Arduino Vcc Vcc Vcc Rx Tx引脚11 Tx Rx引脚10 Gnd Gnd Gnd 键Vcc引脚9 HC06 USB至TTL Vcc Vcc Rx Tx Tx Rx Gnd Gnd 第3步:如果不存在或未连接密钥 仅适用于HC05 :如前所述,某些型号的分线板没有按键引脚,而是有一个EN(启用)引脚或WAKE UP引脚,它们可能连接也可能不连接就像STATE引...
HC-05模块是一种基于蓝牙协议的简单无线通信设备,共有6个引脚,其中两个引脚通过stm32的两个含TX和RX...
STATE –The State pin is LOW when unpaired and HIGH when it is paired. RXD –Receive Data connects to TX on MCU. Use a level shifter if using a 5V MCU TXD –Transmit Data connects to RX on MCU GND –Ground VCC –Power in. Must be between 3.6-6V EN –Enable AT mode. This pin ...
HC-05 bluetooth module(with en pin and state pin) 杜邦线若干 连接电路 hc-05_link_board.png arduino code #include<SoftwareSerial.h>SoftwareSerialBT(3,2);//RX TX on the boardvoidsetup(){// put your setup code here, to run once:Serial.begin(9600);//这里应该和你的模块通信波特率一致dela...
Core module use HC-05 slave module, interfaces include VCC, GND, TXD, RXD, KEY, bluetooth state pin (STATE), output low if not connected, high if connected LED indicates the connection status of bluetooth, quick flash means no connectivity, slow flash means entering AT mode, dou...