___JOGINDEXDISTANCE-4.0000-0.25001.0000___SHIFTJOGLOCKtogglesINDEXMODEEnter[X,Y,Z]OrigintosetJOGOFFSETALTERsetsLimitstocurrentpositionDELETEsetsLIMITStomaxtravelWRITEaddsto,F1setscoordinates(MACHINE)X0.0000inY0.0000inZ3.5179in (DISTTOGO)X0.0000inY0.0000inz0.5179in JOGGINGAXIS @FEED1.
如果刀臂在规定时间之后还没有停下,将发出警报627,即ATC Arm Position Timeout(自动换刀装置刀臂位置超时)。 64 (L)Z TOOL CHANGE OFFSET 对于刀塔来说,指的是从原位开关到刀具零位的位移。 64 (M)Z TOOL CHANGE OFFSET 在立式铣床上:用于Z轴;从原位开关到刀具更换位置和机床零位的位移。约为4.6英寸,因此...
Caution:If the A axis (tilt) moves more than 20 degrees past the home position, Push[EMERGENCY STOP] The tilt (A) axis does not home to a horizontal position. The tool change offset parameter has not been set.Set the rotary platter flatness: Refer to theRotary - TR/TRT/T5C - Platter...
电源配给集成电路板 电源分配电路板 门置式风扇热敏BI偶合器 门置式冷却风扇 +12,-12+5伏直流电低压直流电输出输入来自低压供电系统往各集成电路板 交流电源干线电压 输入 T5变压器 115伏交流电输出往低压供电系统 相位检示 停机(自动控制)K7&K1 115伏交流电输入 来自主变压器 POWERSUPPLYPCB 115伏交流电输出 (送...
ERROR / PLEASE INDICATE YOUR ROTARY SURFACE FLAT OR STRAIGHT WITHIN .002" / RESET YOUR TOOL CHANGE OFFSET IF NEEDED. 旋转不平方到 XYZ 轴。指示 0.002 内的盘片表面"/ 重置倾斜轴的刀具更换偏移。 UNEXPECTED SURFACE FOUND. 探头尖端未与 +/-0.1 内的校准球体中心对齐" / 探头尖端太靠近球体表面。将...
Since I was just rotating A, there was no change in the X-Axis position... and it was nowhere near the travel limit. Not sure what changed, but I posted it again and it worked fine with the C disabled. I'm guessing this is where I would define the A-Axis ...
Hey fellas! Here is an actual trading tri-arb bot. However, I don't have much else to say than this: -- WARNING, PLEASE READ -- This bot executes trades based on estimations and on the assumption that prices do not change when orders are sent out!… ...
210 X TOOL CHANGE OFFSET 211 (L) Y TOOL CHANGE OFFSET 211 (M) Y TOOL CHANGE OFFSET 212 A TOOL CHANGE OFFSET 213 (M) B TOOL CHANGE OFFSET 214 Sp D:Y CURRENT RATIO 215 (M) CAROUSEL OFFSET 216 CNVYR RELAY DELAY 217 CNVYR IGNORE OC TIM ...
M34Coolant Spigot Position Down, Increment (+1) M35Coolant Spigot Position Up, Decrement (-1) M36Pallet Part Ready (P) M39Rotate Tool Turret (T#) (Setting 86) M41Spindle Low Gear Override M42Spindle High Gear Override M50Execute Pallet Change (P) (Setting 121 thru,129) ...
Tool at Power Down. A setting that indicates which tool will occupy the first turret position when the machine is powered down. settings A CNC machine control function that an operator can activate, deactivate, or change to suit specific machining conditions. Settings change the way the CHC ...