• Switch A、Switch B 上分别配置 VRRP 备份组监视上行接口,当上行接口出现故障时,降低 路由器在备份组中的优先级。 • Switch A、Switch B 和二层交换机之间启用 MSTP 多实例,并在各实例中指定根桥和备份根 桥。 • 在 Switch A、Switch B 和 Switch E 之间配置 OSPF 路由协议。Switch A 和 ...
交换机vrrp+mstp配置实例 一、组网需求 1、switch a、switch b选用两台锐捷的s5750;switch c、shwich d选 用锐捷的s3750和s3760 2、全网共有两个业务vlan ,为vlan 10、vlan 20 3、Switch a、switch b都分别对两vlan起用两vrrp组,实现两组的业务的负载分担和备份。 4、Switch a、switch b、switch c、...
[LSW2]stp bpdu-protection 2. 配置保护功能, 在各实例的根桥设备的指定端口配置根保护功能 [LSW1-GigabitEthernet0/0/3]stp root-protection [LSW2-GigabitEthernet0/0/3]stp root-protection 3. 配置处于环网中的设备的二层转发功能 [LSW1]vlan batch 10 20 [LSW1-GigabitEthernet0/0/3]port link-type...
第一步,MSTP配置如下: SW1sysname SW1vlan batch 10 20 66interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan allinterface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan all stp region-configuration region-name ntdinstance 10 vlan 10instance 20 vlan 2...
#配置监视接口,监视VLAN 8的虚接口 [S9500-A-Vlan-interface2] vrrp vrid 1 track Vlan-interface 8 reduced 40 (2)配置S9500-B #配置MSTP实例 [S9500-B]stp enable [S9500-B]stp non-flooding [S9500-B]stp region-configuration [S9500-B-mst-region]region-name vrrp [S9500-B-mst-region]instance 2...
配置多生成树 [jrsw1]stp mode mstp //配置生成树模式为多生成树 [jrsw1]stp region-configuration //进入生成树区域配置 [jrsw1-mst-region]region-name vrrp //配置区域名称 [jrsw1-mst-region]revision-level 1 //修订级别为1 [jrsw1-mst-region]instance 10 vlan 10 //配置实例10映射vlan10 ...
1、H3C S9500交换机VRRP+MSTP配置举例1 特性简介VRRP(Virtual Router Redundancy Protocol,虚拟路由冗余协议)是一种容错协议。如下图所示,通常一个网络内的所有主机都设置一条缺省路由(图中的缺省路由下一跳地址为10.100.10.1),主机发往外部网络的报文将通过缺省路由发往三层交换机Switch,从而实现了主机与外部网络的...
H3CTE MSTP+VRRP综合实验 实验拓扑: 实验设备:S5800交换机4台 实验配置重点: vlan 1 # vlan 10 # vlan 20 # vlan 30 # vlan 40 # vlan 101 # stp instance 0 root primary stp instance 1 root primary stp instance 2 root secondary stp enable(H3C默认不开启) stp region-configuration region-name ...
· Switch A、Switch B上分别配置VRRP备份组监视上行接口,当上行接口出现故障时,降低路由器在备份组中的优先级。 · Switch A、Switch B和二层交换机之间启用MSTP多实例,并在各实例中指定根桥和备份根桥。 · 在Switch A、Switch B和Switch E之间配置OSPF路由协议。Switch A和Switch B通过OSPF发布区域A和区域B...
1.MSTP配置 1.配置 VLAN 和端口 请按照图1-12在Device A和Device B上分别创建VLAN 10、20和30,在Device C上创建VLAN 10、 20 和 40,在Device D上创建VLAN 20、30 和 40;将各设备的各端口配置为Trunk端口并允许相应 的VLAN通过,具体配置: DeviceA ...