[DeviceB-ospf-1] import-route direct [DeviceB-ospf-1] area 0 [DeviceB-ospf-1-area-0.0.0.0] network 10.1.0.0 0.0.0.255 [DeviceB-ospf-1-area-0.0.0.0] network 192.168.0.0 0.0.0.255 [DeviceB-ospf-1-area-0.0.0.0] quit [DeviceB-ospf-1] quit ...
[DeviceB-bgp-default-ipv4] import-route direct [DeviceB-bgp-default-ipv4] quit [DeviceB-bgp-default] quit #在Device C上创建本地AS号为100的BGP实例,指定对等体13.13.13.1和35.35.35.5,并引入直连路由。 [DeviceC] bgp 100 [DeviceC-bgp-default] router-id 3.3.3.3 ...
[Quidway]ip route-static <ip><mask>{interface number|nexthop}[value][reject|blackhole] 例如: [Quidway]ip route-static 129.1.0.0 16 10.0.0.2 [Quidway]ip route-static 129.1.0.0 255.255.0.0 10.0.0.2 [Quidway]ip route-static 129.1.0.0 16 Serial 2 [Quidway]ip route-static 0.0.0.0 0.0.0.0 ...
import-route direct //引入直连路由 import-route ospf 100 //引入OSPF路由 aggregate 192.168.64.0 18 detail-suppressed //配置路由聚合,并抑制发布具体路由 balance 2 //配置负载分担数 default med med-value //配置med缺省值 compare-different-as-med //配置允许比较来自不同AS路由的MED属性值 peer 3.3.3.3...
[R2-ospf-1]import-route direct [R2]ip ip-prefix 1234 deny 192.168.3.100 32 [R2]ip ip-prefix 1234 permit 0.0.0.0 0 less-equal 32 [R2]rip [R2-rip-1]filter-policy ip-prefix 1234 import --- [R3]int s0/2/0 [R3-Serial0/2/0]ip add 10.1.23.2 30 [R3-Serial0/2/0]int s0/2/1...
[SwitchA] route-policy static2rip permit node 10 # 启动RIP协议,同时应用路由策略static2rip对引入的静态路由进行过滤。 [SwitchA] rip [SwitchA-rip-1] import-route static route-policy static2rip 2)配置Switch B # 配置接口vlan-interface 100的IP地址。
[SwitchD–isis-1-ipv4] import-route rip level-2 # 显示Switch C的IS-IS路由信息。 [SwitchC] display isis route Route information for IS-IS(1) --- Level-1 IPv4 Forwarding Table --- IPv4 Destination IntCost ExtCost ExitInterface NextHop Flags --- 10.1.1.0/24 10...
[Quidway-ospf]import-route direct ;引入直联路由[Quidway-Serial0]ospf enable area ;配置OSPF区域标准访问列表命令格式如下:acl [match-order config|auto] ;默认前者顺序匹配。rule [normal|special]{permit|deny} [source source-addr source-wildcard|any]例:[Quidway]acl 10[Quidway-acl-10]rule normal ...
[RT1-ospf-1]import-route direct//注意:配置该指令后引入的路由即为OSPF外部路由 RT3配置: [RT3]rip [RT3-rip]import-route ospf-ase//注意:由于RT1上OSPF引入的直连路由变成了OSPF外部路由,故在这里是引入ospf-ase(OSPF外部路由),而不是引入OSPF [RT3-rip]import-route direct [RT3-rip]ospf [RT3-ospf-...
[Quidway-ospf]import-route direct 引入直联路由 [Quidway-Serial0]ospf enable area 配置OSPF区域 标准访问列表命令格式如下：acl [match-order config|auto] 默认前者顺序匹配。rule [normal|special]{permit|deny} [source source-addr source-wildcard|any] 例：[Quidway]acl 10 [Quidway-acl-...