1.2.48 reset dhcp server ip-in-use 1.2.49 reset dhcp server statistics 1.2.50 static-bind 1.2.51 tftp-server domain-name 1.2.52 tftp-server ip-address 1.2.53 valid class 1.2.54 verify class 1.2.55 voice-config 1.2.56 vpn-instance 1.3 DHCP中继配置命令 1.3.1 dhcp relay check mac-addr...
dhcp select relay 缺省情况下,开启DHCP服务后,接口工作在DHCP服务器模式。 3.5 指定DHCP服务器的地址 3.5.1 指定DHCP中继对应的DHCP服务器地址 1. 功能简介 为了提高可靠性,可以在一个网络中设置多个DHCP服务器。DHCP中继上配置多个DHCP服务器后,DHCP中继会将客户端发来的DHCP报文转发给所有的服务器。 2. 配置限...
1、打开思科模拟软件---按如图配置拓扑图。2、s2960的配置---进入特权模式配置vlan2和vlan3---将fa0/2端口分配到vlan2中，将fa0/3配置到vlan3中---将fa0/1端口模式配置成trunk---end---copy run start。3、3560交换机的配置---进入特权模式配置vlan2和vlan3---在特权模式下输入ip routing...
member interface Route-Aggregation2.200 priority 50 dhcp select relay dhcp relay server-address 10.11.241.200 ip policy-based-route v30-redirect 终端无法从服务器中自动获取IP,手动配置IP上网正常。 2024-04-03提问 举报 (0) 最佳答案 zhiliao_sEUyB dhcp中继,检查下到dhcp服务器的连通性,dhcp的配置 2024...
[SWA-Vlan-interface5]dhcp relay server-address 192.168.7.100 [SWA]int vlan 6 [SWA-Vlan-interface6]dhcp select relay [SWA-Vlan-interface6]dhcp relay server-address 192.168.7.100 3.5 默认路由配置DHCP-server到PC,网关指向192.168.7.1 [DHCP-server]ip route-static 0.0.0.0 0 192.168.7.1...
dhcp relay server-address 10.0.0.10 # interface Vlan-interface20 ip address 10.0.2.254 255.255.255.0 dhcp select relay dhcp relay server-address 10.0.0.10 # interface Vlan-interface30 ip address 10.0.3.254 255.255.255.0 dhcp select relay
dhcp enable # MSR2的配置如下: [MSR2]dis cur # sysname MSR2 # dhcp relay server-group 1 ip 10.10.10.1 # interface Ethernet0/1/0 port link-mode route ip address 20.20.20.2 255.255.255.0 dhcp select relay dhcp relay server-select1 ...
dhcp select relay dhcp relay server-address algorithm master-backup dhcp relay master-server switch-delay 3 dhcp relay server-address 192.168.8.1 dhcp relay server-address 192.168.8.2 quit # 192.168.3.x interface vlan-interface 3 ip address 192.168.3.1 255.255.255.0 dhcp select relay dhcp relay ...
1、打开思科模拟软件---按如图配置拓扑图。2、s2960的配置---进入特权模式配置vlan2和vlan3---将fa0/2端口分配到vlan2中，将fa0/3配置到vlan3中---将fa0/1端口模式配置成trunk---end---copy run start。3、3560交换机的配置---进入特权模式配置vlan2和vlan3---在特权模式下输入ip routing...
[RouterA-GigabitEthernet1/0/0] dhcp select relay 步骤2 在DHCP服务器上进行配置 # 配置RouterB到RouterA与客户端相连接口GE1/0/0的路由。 <RouterB> system-view [RouterB] ip route-static 10.100.0.0 255.255.0.0 202.40.1.1 # 启动DHCP服务。