在Linux驱动中常常会碰到gpio_set_value(port_num,0/1)或gpio_direction_output (port_num,0/1) 这两者有什么关系呢gpio_set_value(port_num,0/1) 一般只是在这个GPIO口的寄存器上写上某个值,至于这个端口是否设置为输出,它就管不了!而gpio_direction_output (port_num,0/1),在某个GPIO口写上某个值之...
最近改驱动程序,看到驱动代码中既有gpio_direction_output也有gpio_set_value。 结论 作用相同,但有差别: gpio_direction_output (port_num,0/1),在某个GPIO口写上某个值的同时,把端口设置为输出模式。 gpio_set_value(port_num,0/1)一般只是在这个GPIO口的寄存器上写上某个值,至于这个端口是否设置为输出,...
pinMode vs gpio_set_direction for UARTby michcfr » Wed Nov 17, 2021 1:37 am Hello, I am using the UART1 (RX:pin16 and TX:pin17) and I need TX to be push-pull output, so I used gpio_set_direction like this: Code: Select all #define Sender_Txd_pin 17 ... gpio_set_...
在这个示例中,我们首先通过 XGpioPs_LookupConfig 函数获取 GPIO 控制器的配置信息,然后使用 XGpioPs_CfgInitialize 函数初始化 GPIO 控制器。接着,我们调用 XGpioPs_SetDirectionPin 函数将引脚 54 设置为输出方向。 4. 注意事项或常见问题 在调用 xgpiops_setdirectionpin 函数之前,必须确保 GPIO 控制器已经正确...
-d <direction>: 设置GPIO的方向,可以是"in"(输入)或"out"(输出)。 -t <nanoseconds>: 设置GPIO的信号输出时间。 gpioset命令示例 示例1:设置GPIO为输出并将值设置为1 gpioset017-dout-v1 1. 示例2:设置GPIO为输入并查询其值 gpioset018-din
gpio_direction_output和gpio_set_value,gpio_direction_outputgpio_direction_output(port_num,0/1),在某个GPIO口写上某个值之后,还会把这个端口设置为输出模式。gpio_set_value(port_num,0/1) 一般只是在这个GPIO口的寄存器上写上某个值,至于这个端口是否设置
before gpio_set_direction, does that fix the problem? Honestly, when I read your response I though to myself I have been using ESP-IDF for years now and have never needed to use gpio_reset_pin(), to make a GPIO pin work properly. There's no way that is the issue. I decided to...
("SetDirection"); gpio_config_t io_conf = {}; io_conf.intr_type = GPIO_INTR_DISABLE; io_conf.mode = GPIO_MODE_OUTPUT; io_conf.pin_bit_mask = (1ULL<<32) ; io_conf.pull_down_en = 0; io_conf.pull_up_en = 1; wait("gpioConfig"); gpio_config(&io_conf); while(true) v...
/* Set the GPIO as a input */ gpio_set_direction(BUTTON1, GPIO_MODE_INPUT); gpio_set_direction(BUTTON2, GPIO_MODE_INPUT); /* Set the GPIO pull */ gpio_set_pull_mode(BUTTON1, GPIO_PULLUP_ONLY); gpio_set_pull_mode(BUTTON2, GPIO_PULLUP_ONLY); ...
Void GPIO_init(){ //myGPIO12 initialization GPIO_setDirectionMode(myGPIO12, GPIO_DIR_MODE_IN); GPIO_setPadConfig(myGPIO12, GPIO_PIN_TYPE_STD); GPIO_setMasterCore(myGPIO12, GPIO_CORE_CPU1); GPIO_setQualificationMode(myGPIO12, GPIO_QUAL_SYNC); ...