一、gpioset的用法 gpioset命令用于设置GPIO的状态,可以将GPIO设置为高电平、低电平或者反转电平。其基本用法如下: 1. 设置GPIO为高电平:gpioset <chip设备编号> <引脚编号>=1 2. 设置GPIO为低电平:gpioset <chip设备编号> <引脚编号>=0 3. 反转GPIO电平:gpioset <chip设备编号> <引脚编号>=2 其中,<chip...
{structgpio_chip*chip=desc->gdev->chip;intstatus;unsignedlongflags;/* 设置label("led-gpios的led").如果为NULL,设置为"?" */desc_set_label(desc, label ? :"?"); status =0;/* 没有"gpio-ranges"属性,无作用 */if(chip->request) {/* mxc_gpio_request */status = chip->request(chip, ...
char强制转换。 其次问题是如何设置gpio2输出低电平,首先查看API文档,API文档正好有函数设置低电平,gpio_set_xxxx函数,就是用来设置的,于是我直接用,然后多次尝试并没有让GPIO2变低(通过电压表可以测量)。这时我就有点懵逼了,明明和API做的一模一样,就是不行,于是我又在乐鑫官网搜索GPIO,正好有一篇文档,正好把文...
在中断处理函数中,调用gpio_get_value/gpio_set_value()函数来获取/设置gpio端口的值,在这里简单分析一下内核的实现流程。 tmp = gpio_get_value(S5PV210_GPH2(0));#definegpio_get_value __gpio_get_valueint__gpio_get_value(unsigned gpio) {structgpio_chip *chip;intvalue; chip=gpio_to_chip(gpio)...
;/* turn on Chip Select */set_gpio( sc, GPCR2,get_gpio( sc, GPCR2 ) | PS11 );/* write TX to data register */set_ssp2( sc, SSDR_2, tx );/* turn off Chip Select */set_gpio( sc, GPSR2,get_gpio( sc, GPSR2 ) | PS11 );/* wait for TX FIFO not to be full */wh...
gpio_set_value(0, 1) ; 读的时候是这样写的: unsigned int uValue1 = 0 ; unsigned int uValue2 = 0 ; unsigned int uValue3 = 0 ; unsigned int uValue37 = 0 ; uValue1= gpio_get_value(1) ; uValue1 = (uValue1 >> 1) & 0x00000001 ; ...
;/* Enable PMIC */gpio_set_level(GPIO_PMIC_EN,1); } 开发者ID:coreboot,项目名称:chrome-ec,代码行数:28,代码来源:board.c 示例2: command_gpio_get ▲点赞 6▼ staticintcommand_gpio_get(intargc,char**argv){intchanged, v, i;/* If a signal is specified, print only that one */if(...
现在要确认的是,如果您给GPIO配置为输出模式,那这个口的输出状态是由您设定的,比如set output level high/low,那这个时候只有在设定的时候用XMC_GPIO_CHECK_OUTPUT_LEVEL来确认是否设定正确。如果是配置为输入模式则可以使用XMC_GPIO_GetInput(),这个函数是获取当前GPIO口的逻辑value。 如我之前...
I am working on the i.MX93-EVK board. I flashed the imx-image-full-imx93evk.wic file from the LF_v6.6.52-2.2.0_images_IMX93EVK folder. When I try to set GPIO 14 to 1, it only changes the direction of the pin but does not set the pin to high. Tags: imx93 ...
The while loop below can be replaced with user application code. */ while(1U) { pin_status = XMC_GPIO_GetInput(XMC_GPIO_PORT1, 15); if(pin_status == 1) { XMC_GPIO_SetOutputHigh(XMC_GPIO_PORT1, 0); } } } 已解决! 转到解答。Like 回复 订阅 49 次查看 0 1 条回复 ...