第一个函数 GPIO_SetBits(GPIOD,GPIO_Pin_2); 当该函数被程序执行的时候,会改变I/O对应寄存器的值,让I/O口PD2输出电压3v3,于是led就被点亮了. 第二个函数 GPIO_ResetBits(GPIOD,GPIO_Pin_2); 当该函数被程序执行的时候,就会把寄存器的逻辑电平改成0,那么I/O口PD2实际的输出电压就会变成0v了,于是LED也...
在嵌入式系统中,特别是在微控制器(MCU)的上下文中,"port" 和 "GPIO"(General Purpose Input/Output)是相关但不同的概念。下面是它们之间的关系: 1.Port(端口): "Port" 通常是指 MCU 上的一组物理引脚或管脚,这些引脚可以用于输入或输出数字信号。 MCU 的端口通常由一组引脚组成,每个引脚可以用于不同的目的...
behind the scenes, the STM32 microcontroller on your board separates the pins into groups calledGPIO ports. Each GPIO port is given a letter, so for example,there’s GPIO port A, port B, and so on[1]. The pins on a GPIO port are givenbit ...
确认led_pin、led_gpio_port和dht11_pin这些宏的完整和正确的定义: #define led_pin gpio_pin_13:这个宏定义看起来是正确的,它定义了一个名为led_pin的宏,其值为gpio_pin_13。这通常表示LED连接到GPIO端口的第13号引脚。但是,需要确保gpio_pin_13在当前编程环境中是有效的。在STM32等微控制器中,通常会...
这段代码是一个嵌入式C语言函数,目的是根据给定的gpio_port和gpio_num参数来确定特定GPIO端口对应的寄存器地址,并设置该GPIO端口的QSEL值。 函数中定义了一个静态函数c28_qualifier_reg_addr()和一个静态函数c28x_set_gpio_qsel()。 c28_qualifier_reg_addr()函数通过switch语句根据给定的gpio_port值判断使用哪个...
LED输出反转
BusFault: A precise (synchronous) data access error has occurred. Possible BusFault location: 0x40049000. HardFault: A fault has been escalated to a hard fault. Again, as before, the fault is thrown on this line in PINS_Init: uint32_t regValue = config->base->PCR[config->pinPortIdx]...
如果都是推挽输出,但是我在KL16Z手册里的第6页看到了有提到开漏输出,所以有点糊涂了,是不是PORT口本身是开漏,可以通过寄存器配置内部上拉或下拉,但是配置称GPIO模式的时候,pin脚输出就变成推挽的了? 0 Kudos Reply 01-22-2015 07:36 PM 2,349 Views Paul_Tian ...
Two things I see at first glance: DMA_Start((void *)array, (void *)(&Pins_DR)); // You need the address ao Pins_DR !! and in DMA
For NXP (founded by Philips) LPC2212 — GPIO Port 0: 30-Bit Simulation support for this peripheral or feature is comprised of: Dialog boxes which display and allow you to change peripheral configuration. VTREGs (Virtual Target Registers) which support I/O with the peripheral. ...