c. Generic pin multiplexing node和Generic pin configuration node 在上图左边的pin controller节点中,有子节点或孙节点,它们是给client device使用的。 可以用来描述复用信息:哪组(group)引脚复用为哪个功能(function); 可以用来描述配置信息:哪组(group)引脚配置为哪个设置功能(setting),比如上拉、下拉等。 注意:p...
int GPIO_SetValue(int gpioFd, GPIO_Value_Type value); ParametersgpioFd The file descriptor for the GPIO. value The GPIO_Value value to set - GPIO_Value_High or GPIO_Value_Low.ErrorsReturns -1 if an error is encountered and sets errno to the error value.EINVAL: the value is not a GP...
enum gpio_override { GPIO_OVERRIDE_NORMAL = 0, ///< peripheral signal selected via \ref gpio_set_function GPIO_OVERRIDE_INVERT = 1, ///< invert peripheral signal selected via \ref gpio_set_function GPIO_OVERRIDE_LOW = 2, ///< drive low/disable output GPIO_OVERRIDE_HIGH = 3, ///< ...
if((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE){/* Enable AFIO Clock */__HAL_RCC_AFIO_CLK_ENABLE();temp = AFIO->EXTICR[position >>2u];CLEAR_BIT(temp, (0x0Fu) << (4u* (position &0x03u)));SET_BIT(temp, (GPIO_GET_INDEX...
代码语言:javascript 代码运行次数:0 运行 AI代码解释 int hal_gpio_pinmux_set_function(gpio_pin_t pin, gpio_muxsel_t function_index); 参数: pin:pin id function_index:需设置的复用功能 返回值 -1:失败 0:成功 获取指定 GPIO 的复用功能 函数原型: ...
GPIO_SetBits(GPIOA, GPIO_Pin_5); 4.2.3 将指定引脚设置为低电平 函数声明如下: void GPIO_ResetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin); GPIOx:要操作的GPIO端口,可以是GPIOA、GPIOB、GPIOC、GPIOD、GPIOE、GPIOF或GPIOG。 GPIO_Pin:要设置为低电平的引脚编号,取值范围为0-15。 使用方法...
void gpiod_set_ raw_value_cansleep(struct gpio_desc *desc, int value) int gpiod_direction_ output_raw(struct gpio_desc *desc, int value)1 2 3 4 5 6 7 8 9 10 11 raw- value的意思就是不在乎DTS里面的ACTIVE,我set高电平,就是高电平。 逻辑关系汇总如下: Function (example) active-low ...
GPIO 通常有多种功能,需要配置 MUX 选择需要的功能,使用hal_gpio_pinmux_set_function(gpio_pin_t pin, gpio_muxsel_t function_index);来设置 GPIO 的复用功能,这里配置为GPIO 输入模式(GPIO_MUXSEL_IN) 代码语言:javascript 代码运行次数:0 运行
GPIOPadConfigSet(SLAVE_INT_BASE[i], SLAVE_INT_PIN[i],GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU); //ROM_IntEnable(INT_GPIOD); ROM_GPIOIntTypeSet(SLAVE_INT_BASE[i],SLAVE_INT_PIN[i],GPIO_RISING_EDGE); //GPIOIntEnable(SLAVE_INT_BASE[i],SLAVE_INT_PIN[i]); ...
(2)初始化key/button去抖所需要的定时器,注意gpio_set_debounce可能会失败,如果失败的话(4)的setup_timer会完成key/button的去抖功能。 (3)获取gpio所对应的irq,该irq为系统维护该gpio中断相关的所有操作的句柄参数。 (4)初始化key/button中断处理的bottom level处理workqueue,初始化key/button去抖定时器,gpio_ke...