void GPIO_Configuration(void) { GPIO_InitTypeDef GPIO_InitStructure; NVIC_InitTypeDef NVIC_InitStructure; EXTI_InitTypeDef EXTI_InitStructure; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOG | RCC_APB2Periph_AFIO,
1.17、void GPIO_EXTILineConfig(uint8_t GPIO_PortSource, uint8_t GPIO_PinSource) 功能:选择GPIO管脚用作外部中断线路。 参数:GPIO_PortSource为选择用作外部中断线源的GPIO端口;GPIO_PinSource为待设置的外部中断线路。 2、硬件设计 由于本次教程为点亮LED,需用到LED。开发板上带有两个LED灯(LED1和LED2),用...
题目 用STM32F4标准外设库开发中,语句“SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, uint8_t EXTI_PinSource4);”的作用是?( ) A.将外部中断4映射到GPIOA的所有引脚上B.将外部中断4与PA4引脚进行映射C.为PA4引脚的中断设置优先级D.使能GPIOA管脚的时钟 相关知识点: 试题来源: 解析 B 反馈 收藏 ...
PinPullConfig – 其中一个 PullDefault – 使用 SOC 定义的开机默认上下拉配置 PullUp - 启用上拉电阻 下拉- 启用下拉电阻 PullNone – 禁用所有上拉/下拉电阻 FunctionNumber – 要编程到多路复用器中的功能编号。 ResourceSource – 引脚复用服务器的 ACPI 命名空间路径 ResourceSourceIndex – 将此设置为 0 ...
Rockchip Pin的ID按照 控制器(bank)+端口(port)+索引序号(pin) 组成。 控制器和GPIO控制器数量⼀致 端口固定 A、B、C和D,每个端口仅有8个索引号,(A=0,B=1,C=2,D=3) 索引序号固定 0、1、2、3、4、5、6、7 rk356x具有5个GPIO控制器,每个控制器可以控制32个IO,作为GPIO功能时,端口⾏为由...
一個pin通常可被設定成input、output、alternate function或analog,input會有兩種狀態表現(floating, pull-up/down),output也有兩種狀態表現(push-pull with pull-up/pull-down or open drain with pull-up/down)。 input/output方向解說 : input是指記憶體方接收來自設備的訊號源,output是指記憶體傳送訊號給設備。
The microcontroller itself (theATmega 328P) is a tiny chip plugged into the Arduino board, and the Arduino board provides a beginner-friendly interface with a USB port, pin headers, DC power jack, among other things to help you program or connect things to it more easily. I encourage you...
The live GPIO pin monitoring library sets up the ESP32 to stream information about what all of the pins are doing in real time to a webserver, which displays the information as a helpful graphic. The demonstration in the video below shows and example troubleshooting a situation where the code...
PORT3: /sys/class/gpio/gpiochip64 PORT4: /sys/class/gpio/gpiochip96 PORT5: /sys/class/gpio/gpiochip128 Calculate the Linux GPIO number for a certain GPIO pin by adding the GPIO pin index to the port base index. For instance: i.MX8M Nano GPIO2_IO4 (port 2, pin 4) is: 32...
If you look at the pin control definitions in arch/arm64/boot/dts/freescale/fsl-imx8mq-var-dart-common.dtsi in the Linux kernel source tree, the number to the right of the pin mux macro can be used for additional attributes like pull-up, slew rate, open drain, drive strength, etc....