(Roundness) 圆度 Cylindricity 圆柱度 Profile of a Line 线轮廓度 Profile of a Surface 面轮廓度 Angularity 倾斜度 Perpendicularity 垂直度 Parallelism 平行度 Position 位置度 Concentricity 同轴度 Symmetry 对称度 Circular Runout * 圆跳动 Total Runout * 全跳动 修正符号 Modifier Symbols Term Maximum ...
(ROUNDNESS) NEVER FORM CYLINDRICITY PROFILE OF A LINE SOMETIMES PROFILE FROFILE OF A SURFACE ANGULARITY PERPENDICULARITY ORIENTATION PARALLELISM POSITION CONCENTRICITY LOCATION SYMMETRY CIRCULAR RUNOUT ALWAYS RUNOUT TOTAL RUNOUT 2 用符号用符号用符号用符号 下图所示是在工程图中几何公差或其他尺寸要求使用最...
(ROUNDNESS) NEVERFORM CYLINDRICITY PROFILEOFALINE SOMETIMESPROFILE FROFILEOFASURFACE ANGULARITY PERPENDICULARITY ORIENTATION PARALLELISM POSITION CONCENTRICITY LOCATION SYMMETRY CIRCULARRUNOUT ALWAYS RUNOUT TOTALRUNOUT 2 X Y14.5M-1982 NONE F T R CR SR X 8X 150 Common Symbols Shown below are the most ...
location, and orientation as well. But instead of checking individual cross-sections (as in circular runout), it checks the entire surface. Thus, using total runout gives us stricter control on the feature’s characteristics.
Runout 跳动 / Circular Runout * 圆跳动 Total Runout * 全跳动其它符号Other Symbols0Diameter 直径其它符号Other Symbols 0 Diameter 直径 R Radius 半径 S0 Spherical Diameter 球径 CR Controlled Radius 控制半径 (25) Reference参考尺寸 SR Spherical Radius 球半径 - All Around 全周 I 25 I Basic ...
Automated 3D geometry measurements inside a drilled rivet hole. The 3D point cloud was analyzed with PolyWorks InspectorTM. List of 3D measurements and GD&T parameters The tables below list the types and examples of dimensional measurements and GD&T parameters that may be obtained from 3D point...
9.6 Total Runout 9.9 Run-Out With Plane as Datum 9.10 Run-Out Relative to Datum Surface and a Diameter 9.12 Run-Out With Two Datum Diameters 9.13 Multiple Cylinders Related to Each Other Runout Application 9.14 Runout Relating Separate Features to Each Other with Common Datum...
As mentioned in the above examples, the profile of a surface can effectively replace almost all of the form and location tolerances. So the question then becomes:Why isn’t it used everywhere?The answer boils down to pricing. In order to measure the surface profile, the part has to be ...
FLATNESS CIRCULARITY (ROUNDNESS) CYLINDRICITY SOMETIMES PROFILE PROFILE OF A LINE FROFILE OF A SURFACE ALWAYS ORIE 18、NTATION ANGULARITY PERPENDICULARITY PARALLELISM LOCATION POSITION CONCENTRICITY SYMMETRY RUNOUT CIRCULAR RUNOUT TOTAL RUNOUT 2 用符号下图所示是在工程图中几何公差或其他尺寸要求使用最广泛的...
total runout 全跳动 d. concentricity 同心度 30. Position also controls ___. 位置度同时也操纵___。 a. perpendicularity 垂直度 c. circularity 圆度 b. datum precedence 基准的顺序 d. roundness 圆度 31. When parallelism is controlled, ___ is also controlled. 当平行度受到操纵时,___也受到...