Return to main program */ 99=>{ if(DEBUG_LEVEL_0==true){ println!("M:{}子命令",_subcommand_integer_part); } }// end M99 /* * M228:Macro for Go To Positions * It takes a P(1-14) parameter for which position it goes to, * follow in the order that the positions are listed...
All coordinates from now on are relative to the last position. G92: Set Position Example: G92 X10 E90 Allows programming of absolute zero point, by reseting the current position to the values specified. This would set the machine's X coordinate to 10, and the extrude coordinate to 90. No...
4.2.1GO: Rapid move 4.2.2Gl: Controlled move 4.2.3G2&Move to Origin 4.3Unbuffered G commands 4.3.1G4:Dwell 4.3.2G20: Set Units to Inches 4.3.3G21: Set Units to Millimeters 4.3.4G90: Set to Absolute Positioning 4.3.5G91: Set to Relative Positioning 4.3.6G92: Set Position 4.4 Unb...
Set SD position 4.4.11 M27: Report SD print status 4.4.12 M28: Begin write to SD card 4.4.13 M29: Stop writing to SD card 4.4.14 M40: Eject 4.4.15 M41: Loop 4.4.16 M42: Stop on material exhausted 4.4.17 M43: Stand by on material exhausted 4.4.18 M80: ATX Power On 4.4.19 M8...
SetSDposition 4.4.11M27:ReportSDprintstatus 4.4.12M28:BeginwritetoSDcard 4.4.13M29:StopwritingtoSDcard 4.4.14M40:Eject 4.4.15M41:Loop 4.4.16M42:Stoponmaterialexhausted 4.4.17M43:Standbyonmaterialexhausted 4.4.18M80:ATXPowerOn 4.4.19M81:ATXPowerOff 1 4.4.20M84:Stopidlehold 4.4.21M92:Set...
echo >>>"data.csv" move.axes[0].machinePosition^","^move.axes[1].machinePosition^","^move.axes[2].machinePosition echo >>>"data.csv" ","^heat.heaters[0].current^","^heat.heaters[2].current^","^heat.heaters[3].current echo >>"data.csv" ","^sensors.filamentMonitors[0]....
4.4.10M26:SetSDposition 4.4.11M27:ReportSDprintstatus 4.4.12M28:BeginwritetoSDcard 4.4.13M29:StopwritingtoSDcard 4.4.14M40:Eject 4.4.15M41:Loop 4.4.16M42:Stoponmaterialexhausted 4.4.17M43:Standbyonmaterialexhausted 4.4.18M80:ATXPowerOn 4.4.19M81:ATXPowerOff 4.4.20M84:Stopidlehold 4.4.21M92...
G90: Set to Absolute Positioning Example: G90 All coordinates from now on are absolute relative to the origin of the machine. (This is the RepRap default.) G91: Set to Relative Positioning Example: G91 All coordinates from now on are relative to the last position. G92: Set Position Ex...
Set SD position 4.4.11 M27: Report SD print status 4.4.12 M28: Begin write to SD card 4.4.13 M29: Stop writing to SD card 4.4.14 M40: Eject 4.4.15 M41: Loop 4.4.16 M42: Stop on material exhausted 4.4.17 M43: Stand by on material exhausted 4.4.18 M80: ATX Power On 4.4.19 M8...
4.4.10M26:SetSDposition 4.4.11M27:ReportSDprintstatus 4.4.12M28:BeginwritetoSDcard 4.4.13M29:StopwritingtoSDcard 4.4.14M40:Eject 4.4.15M41:Loop 4.4.16M42:Stoponmaterialexhausted 4.4.17M43:Standbyonmaterialexhausted 4.4.18M80:ATXPowerOn 4.4.19M81:ATXPowerOff 4.4.20M84:Stopidlehold 4.4.21M92...