","G60": "(保存当前位置)保存当前位置到指定槽","G61": "(返回保存位置)返回指定槽的保存位置","G76": "(探头温度校准)校准探头温度补偿","G80": "取消当前运动模式(G0 G1 G2 G3 G5 G38.X)","G90": "使用绝对坐标系,一般都用绝对坐标系","G91": "使用相对坐标系","G92": "设
voidLoop(){//如果cmdbuffer有空间,则读取G-code指令//读取G-code的buffer为cmdbuffer[BUFSIZE][MAX_CMD_SIZE],BUFSIZE为4,//最多存4条指令。MAX_CMD_SIZE为96,一条指令最多存96个字元。if(buflen<(BUFSIZE-1))get_command();#ifdefSDSUPPORTcard.checkautostart(false);#endifif(buflen){#ifdefSDSUPPOR...
and the value is appended as a decimal integer to the command after the * character. The RepRap firmware expects line numbers to increase by 1 each line, and if that doesn't happen it is flagged as an error. But you can reset the count using M110 (see below). Buffered G Commands Th...
reprapwiki 上面的Gcode 说明 G-code FromRepRapWiki (RedirectedfromGcode) Jumpto:navigation,search Contents[hide] 1Introduction 2RepRapGCodeFields 3Comments 4Individualcommands 4.1Checking 4.1.1Nand* 4.2BufferedGCommands 4.2.1G0:Rapidmove 4.2.2G1:Controlledmove 4.2.3G28:MovetoOrigin 4.3UnbufferedGc...
reprap wiki上的g代码的说明 g 代码 从重复维基 重定向自g代码 Jump to: navigation,search 内容隐藏 1 Introduction 2重复g代码字段 3 Comments 4 Individual
and the value is appended as a decimal integer to the command after the * character. The RepRap firmware expects line numbers to increase by 1 each line, and if that doesn't happen it is flagged as an error. But you can reset the count using M110 (see below). Buffered G Commands ...
and the value is appended as a decimal integer to the command after the * character. The RepRap firmware expects line numbers to increase by 1 each line, and if that doesn't happen it is flagged as an error. But you can reset the count using M110 (see below). Buffered G Comman...
and the value is appended as a decimal integer to the command after the * character. The RepRap firmware expects line numbers to increase by 1 each line, and if that doesn't happen it is flagged as an error. But you can reset the count using M110 (see below). Buffered G Commands ...
G command GCODE_G0_1():提取G0/G1的数据命令,移动命令的数据预处理,在屏上刷新一次坐标。 GCODE_G2():获取弧坐标并移动。 GCODE_G4():暂停命令。 GCODE_G20():设置当前所有距离的单位为英尺。 GODE_G21():设置当前所有距离的单位为毫米。
G90/G91 Influence Extruder- IfUse Octoprint Feature Settingsis unchecked,Arc Welderwill use this setting to determine if the G90/G91 command influences your extruder's axis mode. In general, Marlin 2.0 and forks should have this box checked. Many forks of Marlin 1.x should have this uncheck...