在主菜单中点“advanced”,接下来的菜单中有个“forwarding”,设置如下: extport: 25 to 25 ip address:192.168.1.2 然后点击“apply”就可以了。 宽频蓝色小精灵路由器中设置端口映射 在高级设置页面下点“Distributed Servers Setup(Virtual Serves,虚拟主机设置)” 每个Virtual Server 定义为一个Service Port,...
这样的设定功能在目前市面上 的Router几乎都可以见到,可能的功能名称叫做'Port Forwarding','NAT Server' 或是'Virtual Server' 以FTP服务器为范例,您必须转发埠号21至Turbo NAS的LAN IP,例如转发TCP埠号21至 192.168.1.34。 当NAT router接到自WAN端至外部埠号21的封包时,router将转发该封包至Turbo NAS的LAN...
最后，点击提交。在主菜单中点advanced，接下来的菜单中有个forwarding，以在内部pc192.168.1.2上架设webserver为例设置如下：extport:80to80 ipaddress:192.168.1.2 然后点击“apply”就可以了。http://zhidao.baidu.com/question/6882168.html 参考资料：http://www.138soft.org/BlackHole/router/...
QNAP威联通NAS架设FTP服务器轻松架设一台属于自己的文件传输服务器(FTPServer)文件传输服务器(FTPServer):让你方便的分享与交换大档案的好方法无论是上班时传送档案,或在学校交作业时,大家或许都有这种经验,常常一份档案大小就超过10MB,根本很难用E-mail寄送出去,这让我们想传送这种大档案给其他人,时常无计可施。
We are trying to migrate one of our FTP servers from windows 2003 to windows 2012 R2. After we set up the new FTP Site in 2012 server, we tried to run some FTP commands in cmd and getting the output as below.When I run FTP command “RENAME File1 File.tmp” and File1 doesn’t ...
Can't Boot into Safe Mode - Server 2008 R2 Can't browse by computer name, but can with IP address Can't connect after changing RDP Port Can't create Shadow copy for D Data disk on C System disk Windows Server 2008R2 Can't create sub-ou under Computers builtin OU AD 2008 (mixed)...
tcpdump tcp and host192.168.0.111and port80-s0-c1000-w/tmp/1.cap 回放target.cap文件里的内容 tcpdump -r ./target.cap 查ASCII码表得"GET+空"的十六进制是0x47455420,因此表达式应为tcp[20:4]=0x47455420,加上-A参数以ASCII码方式显示数据包。
ssh -CfNg -R port2:127.0.0.1:port1 user@host #远程转发 可以将dmz_host的hostport端口通过remote_ip转发到本地的port端口 ssh -qTfnN -L port:dmz_host:hostport -l user remote_ip #正向隧道,监听本地port 可以将dmz_host的hostport端口转发到remote_ip的port端口 ...
I don't think it's related to the firewall/portforwarding, since I have my server in the DMZ temporarily while testing and I've disabled the CentOS firewall. Actually, all my firewall/router settings are the same ones that resulted in the successful ftp sessions I had yesterday (it was...
I have been trying to set up an FTP server at home with limited results. I'm running W2K pro with a DSL connection behind a Linksys 4 port router with a NAT firewall. I have enabled port forwarding for ports 20&21 (FTP), and forwarded them to the IP address of my system. Users ...