ftdi vid_pid 0x0B6B 0x0040 ftdi layout_init 0x0860 0x0b7b ftdi channel 0 ftdi layout_signal JTAGOE -data 0x0010 ftdi layout_signal nTRST -data 0x0020 ftdi layout_signal nSRST -data 0x0040 ftdi layout_signal SWD_EN -data 0x0100 ftdi layout_signal SWDIO_OE -data 0x0200 ftdi layout_s...
ftdi_layout_init 0x0058 0x99fb # Signal Data Direction Notes # TCK 0 1 (out) # TDI 0 1 (out) # TDO 0 0 (in) # TMS 1 1 (out) JTAG IEEE std recommendation # LED 1 1 (out) LED off # SWD_EN 0 1 (out) OpenOCD sets this high for SWD # SWDIO_OE 1 1 (out) Ext. buf...
J5 Pin number 1 2 3 4 5 6 7 8 9 10 J5 Signal MPSSE pin number MPSSE Signal MPSSE Lead Color SCK 2 SK ORANGE MOSI 3 DO YELLOW MISO 4 DI GREEN CS# 5 CS BROWN INT# 7 GPIOL1 PURPLE PD# 9 GPIOL3 BLUE 5V 1 VCC RED 3.3V - -- GND 10 GND Black GND - -- Table 5-2 – ...
By default, we've set it up so that it matches our FTDI cables. The 6th pin is RTS (as of Arduino IDE v18 this will work perfectly for uploading to 'inos), the power wire is +5V and the signal levels are 3.3V (they are 5V compliant, and should work in the vast majority of 3....
NOTE: If using the C232HM-EDHSL-0(5V) MPSSE cable then the connection is as: J5 Pin number J5 Signal MPSSE pin number MPSSE Signal 1 SCK 2 SK 2 MOSI 3 DO 3 MISO 4 DI 4 CS# 5 CS 5 INT# 7 GPIOL1 6 PD# 9 GPIOL3 7 5V 1 VCC 8 3.3V - - 9 GND 10 GND 10 GND - - ...
NOTE: If using the C232HM-EDHSL-0(5V) MPSSE cable then the connection is as: J5 Pin number J5 Signal MPSSE pin number MPSSE Signal 1 SCK 2 SK 2 MOSI 3 DO 3 MISO 4 DI 4 CS# 5 CS 5 INT# 7 GPIOL1 6 PD# 9 GPIOL3 7 5V 1 VCC 8 3.3V - - 9 GND 10 GND 10 GND - - ...
Figure 4.1 –Vinco Touch-Key Layout Diagram A detailed description of each pin out is given in the next section. 4.2Vinco Touch-Key Shield Connectors : Pins and Signal Description The following Table 4.2 detailed signal description of each pin out Touch- Name Key Pin Table 4.2 – Pin Signal...
B7 Receive line signal detect (RLSD) 0 = inactive 1 = active Layout of the second byte: B0 Data ready (DR) B1 Overrun error (OE) B2 Parity error (PE) B3 Framing error (FE) B4 Break interrupt (BI) B5 Transmitter holding register (THRE) B6 Transmitter empty (TEMT) B7 Error in RCVR...
Layout of the first byte: B0..B3 - must be 0 B4 Clear to send (CTS) 0 = inactive 1 = active B5 Data set ready (DTS) 0 = inactive 1 = active B6 Ring indicator (RI) 0 = inactive 1 = active B7 Receive line signal detect (RLSD) 0 = inactive 1 = active Layout of the second...
greater signal drive strength to be interfaced to the FT245R. This option is configured in the internal EEPROM. Power Management Control for USB Bus Powered, High Current Designs- The PWREN# signal can be used to directly drive a transistor or P-Channel MOSFET in applications where po...