子网掩码、路径长度和priority都保持一致，如下不能支持SSLVPN、PPTP和L2TP建立两个缺省路由，子网掩码、路径长度和priority都保持一致，如下比较透明模式与路由模式的区别如何实现链路负载均衡（1）确认所设置的路由是否生效不能在图形界面的路由监控和命令行下的路由表中显示出来(diagnoseiproutelist)路由>当前路由查看...
(diagnoseiproutelist)策略路由的特点建立在静态路由和直连路由的基础上的通畅不需要指定网关不能在图形界面的路由监控和命令行下的路由表中显示出来(diagnoseiproutelist)发源于防火墙的流量不能使用策略路由按照顺序执行什么是Loopback接口以及如何创建主要用途:可用于GRE通道和IPSec通道的端点用于OSPF,BGP和RIP的RouterID...
2、en Shortest Path First (OSPF)Border Gateway Protocol (BGP)Intermediate System to Intermediate System (IS-IS)FortiGate路由表只显示目前可用的,最佳的静态路由和动态路由没有测量路由路由表的组成部分每个路由表包含以下部分: IP address/maskGateway IP address/interfaceDistanceMetricPriorityDeviceDistance估算每种...
config router static edit 1 set dst 10.0.0.0 255.255.0.0 set priority 0 set device "to_aliyun_test1" next edit 2 set dst 10.0.0.0 255.255.0.0 set priority 10 # Decrease the priority of the route pointing to Tunnel 2. This way, traffic is preferentially transmitted over Tunnel 1. set ...
set ha-priority “HA election priority (1 - 50)” set update-cascade-interface “Enable/disable update cascade interface, default: enable” set update-static-route “Enable/disable updating the static route, default: enable” set status “Enable/disable this link monitor, default: enable” ...
(diagnose ip route list) 发源于防火墙的流量不能使用策略路由 按照顺序执行 什么是Loopback接口以及如何创建 主要用途: 可用于GRE通道和IPSec通道的端点 用于 OSPF, BGP 和RIP的Router ID 用于冗余的路由 用于动态路由的黑洞 只能在命令行下创建 (set type loopback) 启动透明模式 比较透明模式与路由模式的区别 ...
"ROUTE-IN" set route-map-out "ROUTE-OUT" set password XXXXX next end config network edit 1 set prefix 192.168.10.0 255.255.255.0 next end config redistribute "ospf" set status enable end ← BFD を有効 ← 受信ルートを制御 ← 送信ルートを制御 ← BGP で広告するルート ← OPSF へ再...
BGP route is inactive in the routing table after the hub's IPsec tunnel binding interface bounces. 779258 IPsec phase 1 interface does not create the system interface if it is an aggregate member. 780850 IPsec hub fails to delete selector routes when NAT IP changed and IKE crashed. 781917...
config router bgp set as 65505 set router-id 172.31.0.1 set ibgp-multipath enable set additional-path enable set recursive-inherit-priority enable config neighbor-group edit "gr1" set remote-as 65505 set update-source "hub-lo1" set additional-path both set route-reflector-clien...
For the 871 to FGT, you would also need a host specific route so it would know how to get the tunnel up to begin with. So you have alot of things to do and figure out in order to get this working and that would be the 1st hurdles to overcome. Without an ip_address reachable as...