(1)定义速度的方法在下拉菜单 Velocity Specification Method(速度定义方法)中选择,选项包括 Magnitude and Direction(给定速度值与速度方向) 、Components(给定速度分量)和 Magnitude,Normal to Boundary(给定速度值且假定速度垂直于边界) .(2)如果靠近速度入口
1、速度入口边界条件(velocity-inlet):给出进口速度及需要计算的所有标量值。该边界条件适用于不可压缩流动问题。 Momentum动量?thermal温度radiation辐射species种类 DPM DPM模型(可用于模拟颗粒轨迹)multipahse多项流 UDS(User define scalar是使用fluent求解额外变量的方法) Velocity specification method速度规范方法:magni...
双击inlet(mass-flow-inlet)打开对话框,在该对话框中设置流量入口边界条件的各项参数,在Mass Flow Rate中输入605.6kg/s,初始表压设置为200000Pa。在Specification Method下拉列表中选择湍流强度的定义方法,此处选择Intensity and Viscosity Ratio,即用湍流强度和黏性比定义湍流,其值采用默认值10。单击OK按钮,关闭流量入口...
在Zone列表框中选择边界inlet-y,选择Type下拉框选项Velocity-inlet,鼠标点击面板按钮Edit… 弹出参数设置对话框,如图所示。在Momentum标签页下,设置Velocity Manitude参数值为0.3; 选择Specification Method为Intensity and Hydraulic Diameter,设置Tubulent Intensity为5,设置Hydraulic Diameter为0.15。 切换至Thermal面板,设置T...
(a) Enter 22.6 m/s for the Velocity Magnitude. (b) SelectIntensity and Hydraulic Diameter from the Specification Method dropdownlist in the Turbulence group box. (c) Retain the default value of 10% for the Turbulent Intensity. (d) Enter 42 mm for the Hydraulic Diameter. ...
1、边界条件设置问题1、速度入口边界条件velocity-inle。:给出进口速度及需要计算的所有标量值。该边界条件适用于不可压缩流动问题。Momentum动量?thermal温度radiation辐射species种类DPMDPM模型可用于模寸颗粒轨迹multipahse多项流UDSUserdefinescalar是使用fluent求解额外变量的方法Velocityspecificationmethod速度规方法:...
在对话框中设置velocity Magnitude为20 m/s,设置Specification Method为Intensity and Hydraulic Diameter,设置Turbulent Intensity为1%,设置Hydraulic Diameter为0.02 m 设置outlet边界,如下图所示 双击模型树节点Solution > Method,右侧面板中设置Pressure-Velocity Coupling Scheme为Coupled,激活选项Pseudo Transient及High Order...
设置Velocity Magnitude为10 m/s 设置Specification Method为Intensity and Hydraulic Diameter 设置Turbulent Intensity为5% 设置Hydraulic Diameter为0.05 m 点击OK按钮关闭对话框 9.2 出口设置 设置出口边界outlet的边界类型为outflow。 注意: 本案例采用17.0以后版本演示,改变边界类型的方式与早期版本有些许不同,这里使用右...
选择Problem Setup→Boundary Conditions,在Zone栏选择in,在Type下拉列表框中选择velocity-inlet,单击Edit弹出Velocity Inlet面板,在Velocity Specification Method下拉列表框中选择Magnitude/Normal to Boundary,在Reference Frame下拉列表框中选择Absolute,在Velocity Magnitude栏定义入口速度为15m/s;在Specification Method下拉列表...
VelocityInletZoneNamelinletlVelocitySpecificationMethodjMagnitude,NormaItoBoundaryReferenceFrameAbsoluteVelocityMagnitude(m 32、/s)卩。Temperature(kJ|sggTurbulenceSpecificationMethod|intensityandHydraulicDiameterTurbulenceIntensity(%)卩HydraulicDiameter(mJ时constantconstantPressureOutletZoneNameoutletch4constantJ2constantJco?