进入Fluent的Run Calculation界面,如图所示,先点击Calculation运行一次,当出现图中3所指的信息,点击图中2所指的Stop at end of the iteration,停止迭代,再点击Calculation继续进行计算即可正常计算。
求助!fluent停..我想询问一下 大家有没有遇到过这种情况 我fluent按了stop at end of the iteration 但是他没有反应 还是在继续跑 而且stop多按钮还变灰色了 根本没法暂停了 就还一直
在Fluent中打开EDEM耦合截面,开启耦合,在Fluent中读入Data数据,然后同步时间步,查看Fluent和EDEM的当前计算时间是否一致,若不一致,则需要重新回到第一步。 进入Fluent的Run Calculation界面,如图所示,先点击Calculation运行一次,当出现图中3所指的信息,点击图中2所指的Stop at end of the iteration,停止迭代,再点击Calcul...
我想询问一下 大家有没有遇到过这种情况 我fluent按了stop at end of the iteration 但是他没有反应 还是在继续跑 而且stop多按钮还变灰色了 根本没法暂停了 就还一直在跑已经多跑了一个多小时了还是没停下来 我这个程序跑了大概有一天了 不敢乱动他 我之前也遇到过类似的情况 一通乱按 他就直接闪退程序了 ...
我想询问一下 大家有没有遇到过这种情况 我fluent按了stop at end of the iteration 但是他没有反应 还是在继续跑 而且stop多按钮还变灰色了 根本没法暂停了 就还一直在跑已经多跑了一个多小时了还是没停下来 我这个程序跑了大概有一天了 不敢乱动他 我之前也遇到过类似的情况 一通乱按 他就直接闪退程序了 ...
If the problem occursin the middle of the iteration process, then use the following procedure: Stop the iteration Turn off all equations except theturbulence equations Increase turbulence under relaxation factors (URFs) (k and e) to 1 and iterate for 20-50 iterations ...
Table of Contents 1. bugs/Error error 1.1. Process 1928: Received signal SIGSEGV. 1.2. Error: Couldn't intersect threads 6 and 5 (periodic faces). 1.3. Received signal SIGSEGV on Linux 1.3.1. Description 1.3.2. answer 1.3.3. How to specify the number of nodes?
Iter.take can be used to stop infinite zip sequences:>>> Iter('caleb').cycle().enumerate().take(8).collect() [(0, 'c'), (1, 'a'), (2, 'l'), (3, 'e'), (4, 'b'), (5, 'c'), (6, 'a'), (7, 'l')]
SOLVER AND ITERATION---I think if you set shorter time step, it may be good. Or changing little Under-Relaxiation-Factors, it may be good. In my experience, I set 1/3 Under-Relaxiation-Factors as default.� ---�also lower the values of under relaxation factor and use the coupl...
// stop iteration when C is maximum ( saturated) if (C >= Cs) { C = Cs; S = 0.0; } // Assign value C to UDS (User Defined Scalar) C_UDSI(c, t, 0) = C; dS[eqn] = 0.0; // return S;}July 20, 2023 at 1:44 pm Rob Forum Moderator How many scalars did you tel...