flash ROM is write-protected 青云英语翻译 请在下面的文本框内输入文字,然后点击开始翻译按钮进行翻译,如果您看不到结果,请重新翻译! 翻译结果1翻译结果2翻译结果3翻译结果4翻译结果5 翻译结果1复制译文编辑译文朗读译文返回顶部 闪存ROM写保护 翻译结果2复制译文编辑译文朗读译文返回顶部...
Above is a screenshot and log of the problem I encountered. In addition, I found relevant blog on the official website of NXP, but it seems to be of no use, it still shows flash write protection (1. I used unlock kinetis in jlink commander, 2. I also used mass erase, but I didn...
a我们才会发挥潜力 正在翻译,请等待...[translate] aWhere's there a will,there's a way 那里a意志,有方式[translate] a请输入您需要翻译的文本!充实充实 Enrichment enrichment [translate] aflash rom write-protected? 闪光rom写保护?[translate]
你说的型号，我没有硬件，没法试。不过，刷bios,无论刷主板的，还是显卡的，现在其本在官网都能找到rom文件，而且一般都有些工具或者方法说明的。所以在刷之前，先看好你要刷的型号，去官网找吧，找到后先把需要的文件下载下来，然后记住刷bios的方法。要熟记后才去刷。注意：在找到rom时，看看最新的...
If I try to write a particular value to the flash with FLASH_ProgramHalfWord(Address, Data) or FLASH_ProgramWord(Address, Data) an Hard Fault occur. Whether the flash is write protected or not does not change the fault. From what I can gather with the documentation in PM0056 and the ...
1 - The interface to the flash is bad (like incorrect connections, pin assignments, not meeting timing, bad timing parameters etc.) 2 - The flash is write protected. 3 - The flash is corrupt. Jake Translate 0 Kudos Copy link Reply Altera_Forum Honored Contributor II 09-10-...
本人在调试niosII 程序时用到alt_write_flash_block()对片上flash进行块写操作,代码如下,每写四次之后程序就死机了~~~想不出是什么原因造成的,求高手指导~~~void zuo19872020-06-29 18:42:39 PIC18F接口ADE7758 SPI GLITCH Code Protection bit (Data EEPROM not code-protected)// CONFIG6L#pragma config...
uint32_t WRPState; /*!< WRPState: Write protection activation or deactivation. This parameter can be a value of @ref FLASHEx_OB_WRP_State */ uint32_t WRPPage; /*!< WRPPage: specifies the page(s) to be write protected This parameter can be a value of @ref FLASHEx_OB_Write_Protec...
int8_t STORAGE_IsWriteProtected(uint8_t lun); int8_t STORAGE_Read(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len); int8_t STORAGE_Write(uint8_t lun, uint8_t *buf, uint32_t blk_addr, uint16_t blk_len); ...
To write the IEEE address to a chip, manually write the address into the IEEE field (hexadecimal, with a space between each byte) and then push the “Write IEEE address” button. Writing the IEEE address will fail if the flash is write-protected, or the debug command lock is set. If ...