… int i; int ret = 0; int card_id = 0; int device_id = 0; struct dcmi_flash_info_stru flash_info = {0}; unsigned int flash_count = 0; ret = dcmi_get_device_flash_count(card_id, device_id,, &flash_count); … For
* @cleanup: the ->init() function may have allocated resources, ->cleanup() * is here to let vendor specific code release those resources. * @fixup_onfi_param_page: apply vendor specific fixups to the ONFI parameter * page. This is called after the checksum is verified. */ struct nand...
… int i; int ret = 0; int card_id = 0; int device_id = 0; struct dcmi_flash_info_stru flash_info = {0}; unsigned int flash_count = 0; ret = dcmi_get_device_flash_count(card_id, device_id,, &flash_count); … For (i = 0; i < flash_count; i++){ ret = dcmi_get...
const OAL_IOCTL_HANDLER g_oalIoCtlTable[]={{ IOCTL_HAL_POSTINIT, 0, OALIoCtlHalPostInit },{ IOCTL_HAL_GET_HIVE_CLEAN_FLAG, 0, OALIoCtlHalGetHiveCleanFlag },{ IOCTL_HAL_GET_HWENTROPY, 0, OALIoCtlHalGetHWEntropy },{ IOCTL_HAL_GET_IMAGE_SIGNED_STATE, 0, OALIoCtlHalGetImageSignedState...
最后需要将如下代码添加到 \SEGGER\JLink_Vxxx\JLinkDevices.xml 文件中,JLinkDevices.xml 文件主要用于告诉 J-Link 仿真器 i.MXRT600 的 flash 算法文件位置在哪里。至此,i.MXRT600 的初步支持已经加到 J-Link 中。 以i.MXRT600-EVK (Rev.E) 官方开发板为例,使用 Keil MDK (v5.27及以上) 打开 flash ...
(18432K kernel code, 3168K rwdata, 7164K rodata, 3968K init, 1110K bss, 905136K reserved, 65536K cma)[ 0.000000] random: get_random_u64 called from __kmem_cache_create+0x38/0x420 with crng_init=0 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [...
We can see, the code downloading is finished, after this, reset device, configure the board as internal boot mode, then do the POR or the HW reset, we can see the on board LED D34 is blinking, it means the hardware also can boot from the octal flash. ...
Now I can get response to “QRY” keywords. Next it’s trying to fetch vendor and it fails. Error message is “CFI: Unknown command set 0x1402”. I have captured logs for both working and not working u-boot please find files attached. Since dts file is on the processor side (A...
# Spreadtrum SUBSYSTEMS=="usb", ATTRS{idVendor}=="1782", ATTRS{idProduct}=="4d00", MODE="0666", TAG+="uaccess" # MediaTek SUBSYSTEMS=="usb", ATTRS{idVendor}=="0e8d", ATTRS{idProduct}=="0003", MODE="0666", TAG+="uaccess" ...
1- Using FX2LP internal firmware/data (no EEPROM firmware download and no firmware has been downloaded into RAM - first stage, just standard VID/PID/DID), the firmware download is possible thanks to the 0xA0 vendor request, which is the only vendor request available at this stage. 2- 0x...