屈服强度(降伏强度) (Yield strength) 弹性限度、杨氏弹性系数及屈服点elastic limit, Young’s module of elasticity to yield point 伸长度Elongation 断面缩率Reduction of area 破坏性检验destructive inspections 渗透探伤法Penetrate inspection 磁粉探伤法Magnetic particle inspection 放射线探伤法Radiographic inspection ...
A model for the yield strength anomaly of Fe-Al. Philos Mag A 1998, 77, 737-750.George EP, Baker I (1998) A model for the yield strength anomaly of Fe-Al. Phil Mag A77:737–750George EP, Baker I. A model for the yield strength anomaly of Fe-Al. Philosophical Magazine A 1998;...
Magnetization-Enhanced Dislocation Motion and Decreased Yield Strength of 60Fe40Ni Alloy Using a special constant deflection device, the changes in dislocation configuration ahead of a loaded crack tip for 60Fe40Ni alloy, before and after magne... HongqiLI YanbinWANG,WuyangCHU - 《材料科学技术(英...
A detailed examination of the variation of yield stress with temperature in an Fe3Al alloy shows a maximum at a temperature of about 500掳C, slightly below... W.,Liu,and,... - 《Scripta Materialia》 被引量: 13发表: 1998年 Effect of grain size on yield strength of Ni/sub 3/Al and...
SampleProcess VariablesVED (J/mm3)Yield Strength (MPa)Ultimate Tensile Strength (MPa)Elongation at break (%) P (W)V (mm/s)H (mm) #Q2407500.1080374.9 ± 4.0484.9 ± 5.029.3 ± 1.3 –Fe–49Ni (ASTM) in annealed condition16544135 ...
Yield Strength(at .5% extention under load min) Elongation (in 2in. or 50mm min, %) Brinell Hardness(min) Remarks Ksi MPa Ksi MPa 540 200 14 150 铜套、铜板,铜棒,铜管,铜带,铜瓦、铜丝母、大型铜铸件、离心铜套、法兰铜套、大型衬套、黄铜套、青铜套、系列锡青铜系列ZCuSn10P1锡青铜(美标C90...
Since ultra-high strength materials with yield strength higher than 1500 MPa have typically low ductility, those materials must also be selected based on impact and fracture toughness. Maraging steels have superior toughness compared to conventional quenched and tempered ultra-high strength steels, suc...
aOn the other hand, the Fe 79.5Ga15.6Al4.9 ribbon had a fracture stress of 630 MPa and a yield stress of 600 MPa. These ribbons show larger tensile strength than those of as-melted bulk samples whose maximumtensile fracture stresses were 670 MPa in (Fe0.81-Ga0.13Al0.06)98.6 C1.4 另...
Al content showing the influence of different lattice structures and the solid solution hardening effect of Al in Fe(UE:Uniform elongation, TE:Total elongation, UTS:Ultimate tensile strength, YS:Yield strength); (b)work hardening rate measured between 1% and 1.5% plastic strain as a function of...
Yield Strength (MPa):500; Melting Point:1500 C; Thermal Conductivity:46.1 J/G.K; Product Type:Wire; Material:Fecral; Carbon Content:0.05; PCD:No; ET:No; Hole:No; Application:Heating System; Resistivity(Ohmmm2/M):1.35; Working Temperature( C):1250; ...