电池没有电或者你断开过编码器线造成的原点丢失，手动摇到个轴的原点位置，然后改1815APZ，把0改为1关机重启就可以了
1、断电后检查并重新插接B轴伺服放大器相关电缆后试机；2、如果故障依旧，因此推测是由于脉冲编码器故障；3、替换脉冲编码器后安装试机。如显示“EX2561 SERVOBATTERY ABNORMAL；306 APC ALARM: AXIS BATTERY VOLT-AGE 0（B）；300 APC ALARM: AXIS NEED ZRN（B）；307 APCALARM: AXIS BATTERY DOWN I (B)；...
设备断电停机几小时后再开机时,显示“306APCALARM:AXISBATTERYVOLTAGE0(X);306APCALARM:AXISBATTERYVOLTAGE0(Y);306APCALARM:AXISBATTERYVOLTAGE0(Z);“300APCALARM:AXISNEEDZRN(X);300APCALARMAXISNEEDZRN(Y);300APCALARM:AXISNEEDZRN(Z)”。这时切勿关断设备电源,将NC后备电池(4节)更换后,按“RESET”键即可...
设备断电停机几小时后再开机时,显示“306 APC ALARM: AXISBATTERY VOLTAGE 0(X);306 APC ALARM:AXIS BATTERYVOLTAGE 0(Y);306 APC ALARM:AXIS BATTERY VOLTAGE 0(Z);“300 APC ALARM: AXIS NEED ZRN (X);300 APC ALARMAXIS NEED ZRN (Y); 300 APC ALARM: AXIS NEED ZRN (Z)”。这时切勿关断设备...
设备断电停机几小时后再开机时,显示“306 APCALARM:AXISBATTERYVOLTAGE0(X);306APCALARM:AXISBATTERYVOLTAGE0(Y);306APC ALARM:AXISBATTERYVOLTAGE0(Z);“300APCALARM:AXISNEEDZRN(X);300APCALARMAXIS NEEDZRN(Y);300APCALARM:AXISNEED...
设备断电停机几小时后再开机时,显示“306 APC ALARM: AXISBATTERY VOLTAGE 0(X);306 APC ALARM:AXIS BATTERYVOLTAGE 0(Y);306 APC ALARM:AXIS BATTERY VOLTAGE 0(Z);“300 APC ALARM: AXIS NEED ZRN (X);300 APC ALARMAXIS NEED ZRN (Y);300 APC ALARM: AXIS NEED ZRN (Z)”。这时切勿关断设备电源...
300 n AXIS NEED ZRN 301 APC ALARM:n AXIS COMMUNICATION 302 APC ALARM:n AXIS OVER TIME 303 APC ALARM:n AXIS FRAMING 304 APC ALARM:n AXIS PARITY 305 APC ALARM:n AXIS PULSE MISS 306 APC ALARM:n AXIS BATTERY ZERO 307 APC ALARM:n AXIS BATTERY DOWN 1 308 APC ALARM:n AXIS BATTERY DOWN...
OT030 SYNC EXCESS ERROR ALARM 1 OT031 SYNCHRONIZE ADJUST MODE OT032 NEED ZRN (ABS PCDR) OT034 BATTERY ZERO (ABS PCDR) OT035 IMPOSSIBLE ZRN (SERIAL) OT036 BATTERY DOWN (ABS PCDR) OT120 UNASSIGNED ADDRESS (HIGH) OT121 UNASSIGNED ADDRESS (LOW) ...
设备断电停机几小时后再开机时,显示“306 APC ALARM: AXISBATTERY VOLTAGE 0(X);306 APC ALARM:AXIS BATTERYVOLTAGE 0(Y);306 APC ALARM:AXIS BATTERY VOLTAGE 0(Z);“300 APC ALARM: AXIS NEED ZRN (X);300 APC ALARMAXIS NEED ZRN (Y);300 APC ALARM: AXIS NEED ZRN (Z)”。这时切勿关断设备电源...
设备断电停机几小时后再开机时,显示“306 APC ALARM: AXISBATTERY VOLTAGE 0 (X); 306 APC ALARM: AXIS BATTERYVOLTAGE 0 (Y); 306 APC ALARM:AXIS BATTERY VOLTAGE 0(Z);“300 APC ALARM: AXIS NEED ZRN (X);300 APC ALARMAXIS NEED ZRN (Y); 300 APC ALARM: AXIS NEED ZRN (Z)”。这时切勿...