针对这种错误有很多原因,我遇到的是魔术棒没有配置好,要照着下面的图片就配置再烧录就可以烧录成功了。 审核编辑 黄宇
Relocating to 5ff3a000, new gd at 5fe99df8, sp at 5fe99de0NAND: fmc_ip_ver_check(34): Check Flash Memory Controller v100 …fmc_ip_ver_check(40): FoundSPI Nand ID Table Version 2.7SPI Nand(cs 0) ID: 0xc2 0x12 Name:”MX35LF1GE4AB”Block:128KB Page:2KB OOB:64B ECC:4bit/...
里面没有NOR FLASH相关的,我硬件电路是按照http://processors.wiki.ti.com/index.php/Connecting_NOR_Flash_to_OMAP-L138来接的。 谢谢! 向上0True向下 Shine8 年多前回复beifeng zhu TI__Guru***357097points 异步memory的设置在OMAP-L138_FlashAndBootUtils_2_40\OMAP-L138\Common\src\device_async_mem.c...
SDK烧写错误解决SDK烧写错误解决方法SDK烧写错误解决提示 unable to detect JTAG cable 提示ERROR:flashoperationfailed提示 unable to detect JTAG cable解决办法:在programflashmemory 中,在device选择里面去掉Auto Detect前面的√,选择自己的设备 [Vivado 2020.1]ZYNQ7020折腾之路(四)之荔枝糖Hex固化程序到TF卡/NAND FLA...
embedded - Nand partitioning in u-boot - Stack Overflow In linux NAND flash partitions are created in the board file, also "mtdparts" parameter can be used in the Linux boot command as described in sect.4.6 Flash memory maps attached Linux Guide. Best regardsigor---Note: If this...
0 Storage Device(s) found Device 0: unknown device switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... 84282 bytes read in 2 ms (40.2 MiB/s) Unable to open OP-TEE session (err=-5) mm_communicate failed! Error: Cannot initialize UEFI sub-system, r ...
Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x280000, size 0x440000 4456448 bytes read: OK ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-2.6.37 Image Type: ARM Linux Kernel Image (uncompressed) ...
目前工作在嵌入式系统产品中,其中硬件平台是64MB DRAM+128MB NAND FLASH,Linux kernel 5.18, 文件系统是UBIFS。 当排查系统中一个应用进程大量消耗内存的问题过程中,为了获得进程获取/访问内存的调用逻辑,便利用Linux的机制主动引发该进程的core dump,从而根据core dump的back trace来分析访问/消耗内存的可疑点。(如何...
你好, 我们正在使用AM437x这款CPU ,基于'ti-processor-sdk-linux-am437x-evm-05.02.00.10'版本SDK,来调试mass storage功能; 我们尝试了使用,默认内核配置'tisdk_am437x-evm_defconfig',插入U盘时,能正常识别和自动mount
Currently I can run manually from the chainloaded u-boot's prompt. I will post a summary, but basically I'm using 'mmc read' instead of 'load/fatload' to load kernel, ramdisk, and dtb. The issue I run into is that in the mainline u-boot I don't have the 'saveenv' command. I...